turbostat already checks whether calling each cpuid leavf is legal,
and it doesn't look at the function return value,
so call the simpler gcc intrinsic __cpuid() instead of __get_cpuid().
syntax only, no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
The accuracy of Bzy_Mhz and Busy% depend on reading
the TSC, APERF, and MPERF close together in time.
When there is a very short measurement interval,
or a large system is profoundly idle, the changes
in APERF and MPERF may be very small.
They can be small enough that an expensive interrupt
between reading APERF and MPERF can cause the APERF/MPERF
ratio to become inaccurate, resulting in invalid
calculation and display of Bzy_MHz.
A dummy APERF read of APERF makes this problem
much more rare. Apparently this 1st systemn call
after exiting a long stretch of idle is when we
typically see expensive timer interrupts that cause
large jitter.
For the cases that dummy APERF read fails to prevent,
we compare the latency of the APERF and MPERF reads.
If they differ by more than 2x, we re-issue them.
Signed-off-by: Len Brown <len.brown@intel.com>
The column "GFX%c6" show the percentage of time the GPU
is in the "render C6" state, rc6. Deep package C-states on several
systems depend on the GPU being in RC6.
This information comes from the counter
/sys/class/drm/card0/power/rc6_residency_ms,
as read before and after the measurement interval.
Signed-off-by: Len Brown <len.brown@intel.com>
Under the column "GFXMHz", show a snapshot of this attribute:
/sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz
This is an instantaneous snapshot of what sysfs presents
at the end of the measurement interval. turbostat does
not average or otherwise perform any math on this value.
Signed-off-by: Len Brown <len.brown@intel.com>
The new IRQ column shows how many interrupts have occurred on each CPU
during the measurement inteval. This information comes from
the difference between /proc/interrupts shapshots made before
and after the measurement interval.
The first row, the system summary, shows the sum of the IRQS
for all CPUs during that interval.
Signed-off-by: Len Brown <len.brown@intel.com>
skip the open(2)/close(2) on each msr read
by keeping the /dev/cpu/*/msr files open.
The remaining read(2) is generally far fewer cycles
than the removed open(2) system call.
Signed-off-by: Len Brown <len.brown@intel.com>
By default...
Turbostat --debug gconfiguration info goes to stderr.
In FORK mode, turbostat statistics go to stderr.
In PERIODIC mode, turbostat statistics go to stdout.
These defaults do not change, but an option "--out file"
will send all output above only to the specified file.
Signed-off-by: Len Brown <len.brown@intel.com>
some tools processing turbostat output
have difficulty with items that begin with %...
Reported-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Following changes have been made:
- changed MSR_NHM_TURBO_RATIO_LIMIT to MSR_TURBO_RATIO_LIMIT in debug print
for consistency with Developer Manual
- updated definition of bitfields in MSR_TURBO_RATIO_LIMIT and appropriate
parsing code
- added x200 to list of architectures that do not support Nahlem compatible
definition of MSR_TURBO_RATIO_LIMIT register (x200 has the register but
bits definition is custom)
- fixed typo in code that parses MSR_TURBO_RATIO_LIMIT
(logical instead of bitwise operator)
- changed MSR_TURBO_RATIO_LIMIT parsing algorithm so the print out had the
same order as implementations for other platforms
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
Pull block merge fix from Jens Axboe.
This fixes the block segment counting bug and resulting sg overrun
reported by Kent Overstreet, introduced with the last block pull.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't optimize for non-cloned bio in bio_get_last_bvec()
Pull x86 fixes from Ingo Molnar:
"This fixes 3 FPU handling related bugs, an EFI boot crash and a
runtime warning.
The EFI fix arrived late but I didn't want to delay it to after v4.5
because the effects are pretty bad for the systems that are affected
by it"
[ Actually, I don't think the EFI fix really matters yet, because we
haven't switched to the separate EFI page tables in mainline yet ]
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Fix boot crash by always mapping boot service regions into new EFI page tables
x86/fpu: Fix eager-FPU handling on legacy FPU machines
x86/delay: Avoid preemptible context checks in delay_mwaitx()
x86/fpu: Revert ("x86/fpu: Disable AVX when eagerfpu is off")
x86/fpu: Fix 'no387' regression
Pull SCSI target bug fix from Nicholas Bellinger:
"Here is an outstanding target-core bug-fix for v4.5 code."
This patch addresses a recent Task Management (TMR) regression related
to larger set of multi-port LUN_RESET bug-fixes in v4.5-rc5.
It drops a left-over target_put_sess_cmd() of se_cmd->cmd_kref within
ABORT_TASK failure path, once a se_cmd descriptor has already
completed posting response to fabric driver logic, and must be skipped
during normal ABORT_TASK se_cmd->tag lookup"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect ABORT_TASK put for completed commands
For !BIO_CLONED bio, we can use .bi_vcnt safely, but it
doesn't mean we can just simply return .bi_io_vec[.bi_vcnt - 1]
because the start postion may have been moved in the middle of
the bvec, such as splitting in the middle of bvec.
Fixes: 7bcd79ac50d9(block: bio: introduce helpers to get the 1st and last bvec)
Cc: stable@vger.kernel.org
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A few new AVX-512 instruction groups/features are added in cpufeatures.h
for enuermation: AVX512DQ, AVX512BW, and AVX512VL.
Clear the flags in fpu__xstate_clear_all_cpu_caps().
The specification for latest AVX-512 including the features can be found at:
https://software.intel.com/sites/default/files/managed/07/b7/319433-023.pdf
Note, I didn't enable the flags in KVM. Hopefully the KVM guys can pick up
the flags and enable them in KVM.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Link: http://lkml.kernel.org/r/1457667498-37357-1-git-send-email-fenghua.yu@intel.com
[ Added more detailed feature descriptions. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some machines have EFI regions in page zero (physical address
0x00000000) and historically that region has been added to the e820
map via trim_bios_range(), and ultimately mapped into the kernel page
tables. It was not mapped via efi_map_regions() as one would expect.
Alexis reports that with the new separate EFI page tables some boot
services regions, such as page zero, are not mapped. This triggers an
oops during the SetVirtualAddressMap() runtime call.
For the EFI boot services quirk on x86 we need to memblock_reserve()
boot services regions until after SetVirtualAddressMap(). Doing that
while respecting the ownership of regions that may have already been
reserved by the kernel was the motivation behind this commit:
7d68dc3f10 ("x86, efi: Do not reserve boot services regions within reserved areas")
That patch was merged at a time when the EFI runtime virtual mappings
were inserted into the kernel page tables as described above, and the
trick of setting ->numpages (and hence the region size) to zero to
track regions that should not be freed in efi_free_boot_services()
meant that we never mapped those regions in efi_map_regions(). Instead
we were relying solely on the existing kernel mappings.
Now that we have separate page tables we need to make sure the EFI
boot services regions are mapped correctly, even if someone else has
already called memblock_reserve(). Instead of stashing a tag in
->numpages, set the EFI_MEMORY_RUNTIME bit of ->attribute. Since it
generally makes no sense to mark a boot services region as required at
runtime, it's pretty much guaranteed the firmware will not have
already set this bit.
For the record, the specific circumstances under which Alexis
triggered this bug was that an EFI runtime driver on his machine was
responding to the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event during
SetVirtualAddressMap().
The event handler for this driver looks like this,
sub rsp,0x28
lea rdx,[rip+0x2445] # 0xaa948720
mov ecx,0x4
call func_aa9447c0 ; call to ConvertPointer(4, & 0xaa948720)
mov r11,QWORD PTR [rip+0x2434] # 0xaa948720
xor eax,eax
mov BYTE PTR [r11+0x1],0x1
add rsp,0x28
ret
Which is pretty typical code for an EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE
handler. The "mov r11, QWORD PTR [rip+0x2424]" was the faulting
instruction because ConvertPointer() was being called to convert the
address 0x0000000000000000, which when converted is left unchanged and
remains 0x0000000000000000.
The output of the oops trace gave the impression of a standard NULL
pointer dereference bug, but because we're accessing physical
addresses during ConvertPointer(), it wasn't. EFI boot services code
is stored at that address on Alexis' machine.
Reported-by: Alexis Murzeau <amurzeau@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raphael Hertzog <hertzog@debian.org>
Cc: Roger Shimizu <rogershimizu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1457695163-29632-2-git-send-email-matt@codeblueprint.co.uk
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=815125
Signed-off-by: Ingo Molnar <mingo@kernel.org>
i486 derived cores like Intel Quark support only the very old,
legacy x87 FPU (FSAVE/FRSTOR, CPUID bit FXSR is not set), and
our FPU code wasn't handling the saving and restoring there
properly in the 'eagerfpu' case.
So after we made eagerfpu the default for all CPU types:
58122bf1d8 x86/fpu: Default eagerfpu=on on all CPUs
these old FPU designs broke. First, Andy Shevchenko reported a splat:
WARNING: CPU: 0 PID: 823 at arch/x86/include/asm/fpu/internal.h:163 fpu__clear+0x8c/0x160
which was us trying to execute FXRSTOR on those machines even though
they don't support it.
After taking care of that, Bryan O'Donoghue reported that a simple FPU
test still failed because we weren't initializing the FPU state properly
on those machines.
Take care of all that.
Reported-and-tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-cheng <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/20160311113206.GD4312@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Return error immediately to simplify the control flow in pci_create_attr().
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If sysfs_create_bin_file() fails, pci_create_attr() leaks the struct
bin_attribute it allocated previously.
Free the struct bin_attribute if pci_create_attr() fails.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The value of pdev->rom_attr is the definitive indicator of the fact that
we're created a sysfs attribute. Check that rather than rom_size, which is
only used incidentally when deciding whether to create a sysfs attribute.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The IORESOURCE_ROM_COPY and IORESOURCE_ROM_BIOS_COPY bits are unused.
Remove them and code that depends on them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Loongson 3 used the IORESOURCE_ROM_COPY flag for its ROM resource. There
are two problems with this:
- When IORESOURCE_ROM_COPY is set, pci_map_rom() assumes the resource
contains virtual addresses, so it doesn't ioremap the resource. This
implies loongson_sysconf.vgabios_addr is a virtual address. That's a
problem because resources should contain CPU *physical* addresses not
virtual addresses.
- When IORESOURCE_ROM_COPY is set, pci_cleanup_rom() calls kfree() on the
resource. We did not kmalloc() the loongson_sysconf.vgabios_addr area,
so it is incorrect to kfree() it.
If we're using a shadow copy in RAM for the Loongson 3 VGA BIOS area,
disable the ROM BAR and release the address space it was consuming.
Use IORESOURCE_ROM_SHADOW instead of IORESOURCE_ROM_COPY. This means the
struct resource contains CPU physical addresses, and pci_map_rom() will
ioremap() it as needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a temporary struct resource pointer to avoid needless repetition of
"pdev->resource[PCI_ROM_RESOURCE]". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A struct resource contains CPU physical addresses, not virtual addresses.
But sn_acpi_slot_fixup() and sn_io_slot_fixup() stored the virtual address
of a shadow ROM copy in the resource. To compensate, pci_map_rom() had a
special case that returned the resource address directly rather than
calling ioremap() on it.
When we're using a shadow copy in RAM or PROM, disable the ROM BAR and
release the address space it was consuming.
Store the CPU physical (not virtual) address in the shadow ROM resource,
and mark the resource as IORESOURCE_ROM_SHADOW so we use the normal
pci_map_rom() path that ioremaps the copy.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Depositing __IA64_UNCACHED_OFFSET in the upper address bits is essentially
equivalent to ioremap(): it converts a CPU physical address to a virtual
address using the ia64 uncacheable identity map.
Call ioremap() instead of doing the phys-to-virt conversion manually with
__IA64_UNCACHED_OFFSET.
Note that this makes it obvious that (a) we're putting a virtual address in
a struct resource, and (b) we're passing a virtual address to ioremap()
below in the PCI_ROM_RESOURCE case. These are both pre-existing problems
that I'll resolve next.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a temporary struct resource pointer to avoid needless repetition of
"dev->resource[idx]". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove unnecessary indentation in pci_map_rom(). This is logically part of
the previous patch; I split it out to make the critical changes in that
patch more obvious. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When pci_create_sysfs_dev_files() created the "rom" sysfs file, it set the
sysfs file size to the actual size of a ROM BAR, or if there was no ROM BAR
but the platform provided a shadow copy in RAM, to 0x20000. 0x20000 is an
arch-specific length that should not be baked into the PCI core.
Every place that sets IORESOURCE_ROM_SHADOW also sets the size of the
PCI_ROM_RESOURCE, so use the resource length always.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of platforms like Nvidia's Tegra210 Jetson-TX1 platform has
multiple PMW based regulators. Add support to have multiple instances
of the driver by not changing any global data of pwm regulator and
if required, making instance specific copy and then making changes.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With following equation for calculating
voltage_to_duty_cycle_percentage
100 - (((req_uV * 100) - (min_uV * 100)) / diff);
we get 0% for max_uV and 100% for min_uV.
Correcting this to
((req_uV * 100) - (min_uV * 100)) / diff;
to get proper duty cycle.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OF interface provides to read the u32 value via standard interface
of_property_read_u32(). Use this API to read "regulator-min-microvolts"
and "regulator-max-microvolt".
This will make consistent with other property value reads.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
* A simple error code handling fix for the NAND ECC test; this was a
regression in v4.5-rc1
* A MAINTAINERS update, which might as well go in ASAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Got
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160311' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Late MTD fix for v4.5:
- A simple error code handling fix for the NAND ECC test; this was a
regression in v4.5-rc1
- A MAINTAINERS update, which might as well go in ASAP"
* tag 'for-linus-20160311' of git://git.infradead.org/linux-mtd:
MAINTAINERS: add a maintainer for the NAND subsystem
mtd: nand: tests: fix regression introduced in mtd_nandectest
Pull drm/i915 fixes from Dave Airlie:
"Just two i915 regression fixes, that should be it from me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Actually retry with bit-banging after GMBUS timeout
drm/i915: Fix bogus dig_port_map[] assignment for pre-HSW
When removing an element from the mempool, mark it as unpoisoned in KASAN
before verifying its contents for SLUB/SLAB debugging. Otherwise KASAN
will flag the reads checking the element use-after-free writes as
use-after-free reads.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cavium,pci-thunder-ecam devices are exactly ECAM-based PCI root
complexes. These root complexes (loosely referred to as ECAM units in the
hardware manuals) are used to access the Thunder on-chip devices. They
are special in that all the BARs on devices behind these root complexes are
at fixed addresses.
Add a driver for these devices that synthesizes Enhanced Allocation (EA)
capability entries for each BAR.
Since this EA synthesis is needed for exactly two chip models, we can hard-
code some assumptions about the device topology and the layout of the
config space of specific DEVFNs in the driver.
[bhelgaas: changelog, whitespace]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
The root complexes used to access off-chip PCIe devices (called PEM units
in the hardware manuals) on some Cavium ThunderX processors require quirky
access methods for the config space of the PCIe bridge.
Add a driver to provide these config space accessor functions. Use the
pci-host-common code to configure the PCI machinery.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move pci_host_common_probe() and associated functions to pci-host-common.c,
where it can be shared with other drivers. Make it public (not static)
and update Kconfig and Makefile to build it. No functional change
intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Factor gen_pci_probe(), moving most of it into pci_host_common_probe()
where it can be shared with other drivers that have slightly different
config accessors. No functional change intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Move definitions for generic PCI host controller driver structures to a
separate header file so we can share them with other drivers. No
functional change intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Commit 0a927c2f02 ("dm thin: return -ENOSPC when erroring retry list due
to out of data space") was a step in the right direction but didn't go
far enough.
Add a new 'out_of_data_space' flag to 'struct pool' and set it if/when
the pool runs of of data space. This fixes cell_error() and
error_retry_list() to not blindly return -EIO.
We cannot rely on the 'error_if_no_space' feature flag since it is
transient (in that it can be reset once space is added, plus it only
controls whether errors are issued, it doesn't reflect whether the
pool is actually out of space).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips from
premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM and PCI
memory windows were conflicting in some configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/uWT
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips
from premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM
and PCI memory windows were conflicting in some configurations"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=btba
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"One last time fix: It adds a code that prevents some media tools like
media-ctl to hide some entities that have their IDs out of the range
expected by those apps"
* tag 'media/v4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: map new functions into old types for legacy API
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
