This driver has been tested on MX27/MX31. It should work on MX1/MX1
aswell, but the actual setting of the PWM is missing so far.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
v2: As pointed out by Hans J. Koch we have to claim we can do 24bit to
make software like X work. We are lucky on i.MX that 18bit support
has the necessary gaps in the fields to do so.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The in kernel FEC driver has recently been ported to a platform driver.
Add a platform_device for it and register it for pcm038 and mx27ads.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX31ADS supports pluggable PMU modules, including the WM835x based
Wolfson Microelectronics 1133-EV1. These boards provide power, audio,
RTC and watchdiog services to the system. This patch adds initial support
for those boards in I2C mode.
Currently support is limited by the available support for the features
of the i.MX31 in the mainline kernel. Some further work will be needed
once other PMU modules are supported and once there is SPI support.
Many of the regulator constraints will be sharable with other PMU
boards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This example takes advantage of the possibility to use tables of iomux
configs.
This is inspired from mx1-mx2 iomux code. It allows a better code
readability.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This new implemenatation avoids that two physical pins are claimed by
the same driver (also with the the gpr hardware modes).
The gpio kernel lib is also called when a capable gpio pin is assigned
its gpio function.
The mxc_iomux_mode function is still here for backward compatibility but
should not be used anymore.
V2:
In the precendent revision, the iomux code was claiming a pin when its
hardware mode was changed. This was uncorrect: when the hardware mode is
changed, the pin must still be claimed through the iomux.
In order to have a pin working in mode hw2, we must fist issue the
mxc_iomux_set_gpr call and then the corresponding mxc_iomux_mode calls
with the FUNC mode (usually done with mxc_iomux_setup_multiple_pins).
The reverse calls must be done to fee the pins.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
... from both mx27ads.c and pcm038.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Several of the macros in mx31ads.h depend on mx31.h which is no longer
included in quite so many standard headers as it once was. Include it
directly so we can build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX I2C driver has not yet been merged into mainline but it is
near to that and the device defintions don't depend directly on it
so we can add the devices now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch mimicks what Martin wrote on the mailing list:
* move arch/arm/mach-imx/include/mach/imxfb.h into
arch/arm/mach-mxc/include/mach/imxfb.h
* changes Kconfig so that CONFIG_FB_IMX is selectable
* adds a platform device (copied from some pengutronix
patches)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* define new CONFIG_ARCH_MX21 (this one is currently mutually exclusive to
CONFIG_ARCH_MX27, but this might change)
* splits one header file. Memory definitions, interrupt sources,
DMA channels are split into common part, i.MX27 specific and i.MX21
specific.
* guard access to UART5/UART6, which don't exist on i.MX21
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Here are some of the warnings that get fixed by this:
> 200 times: warning: cast adds address space to expression (<asn:2>)
twelve times: warning: symbol 'xxx' was not declared. Should it be static
two times: warning: symbol 'clock' shadows an earlier one
five times: warning: incorrect type in initializer (different address spaces)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch only adds general clkdev support without actually switching
any MXC architecture to clkdev.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- rename mxc_clocks_init to architecture specific versions. This
allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had 3 versions of this function in clock support for MX1/2/3
Use a single one instead. I picked the one from the MX3 as it seems
to calculate more accurate as the other ones. Also, on MX27 and MX31 mfn
can be negative, this hasn't been handled correctly on MX27 since now.
This patch has been tested on MX27 and MX31 and produces the same clock
frequencies for me.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* adds Kconfig variables
* specifies different physical address for i.MX21 because of the
different memory layouts
* disables support for UART5/UART6 in the i.MX serial driver
(the i.MX21 doesn't have those modules)
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* removed iomux-mx1-mx2.h completely
* distributes the former contents to four different files (iomux-mx1.h,
iomux-mx21.h, iomux-mx27.h and the file iomux-mx2x.h, which is common to
both i.MX21 and i.MX27).
* adds all documented IOMUX definitions for i.MX21 and i.MX27
* fixes a few that were wrong (PD14_AOUT_FEC_CLR, PE16_AF_RTCK).
* don't silenly include <linux/io.h>
* and fixes all collateral damage from above
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add gpio vbus detection to udc driver, by taking advantage
of the new gpio_vbus driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CSB701 is one of baseboards that can be used with CSB726 SOM.
This currently adds support for button and LED on the board.
More to come later.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Change the power state of each widget before starting the initialization
work so that all verbs are executed properly.
Also, keep power-up during hwdep reconfiguration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> posted a patch series
to linux-pci to fix a wrong assumption about pci_bus->self==NULL for
all PCI host bus controllers. While PARISC platforms to not behave
this way, I prefer to have the code consistent across architectures.
The following patch replaces pci_bus->self with pci_bus->parent when
used as a test to check for "root bus controller".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Add braces around the macro arguments, else for example
"shl %r1, 5-3, %r2" would not expand to what you would assume.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix compile warnings:
drivers/scsi/zalon.c: In function `zalon_probe':
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_driver_string' from incompatible pointer type
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_name' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix those compile warnings:
uaccess.h:244: warning: `struct pt_regs' declared inside parameter list
uaccess.h:244: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
commit 11c3b5c3e0
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
- convert a few "if (xx) BUG();" to BUG_ON(xx)
- remove a few printk()s, as we get a backtrace with BUG_ON() anyway
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
