ARMv6K CPUs have SEV (send event) and WFE (wait for event) instructions
which allow the CPU clock to be suspended until another CPU issues a
SEV, rather than spinning on the lock wasting power. Make use of these
instructions.
Note that WFE does not wait if an event has been sent since the last WFE
cleared the event status, so although it may look racy, the instruction
implementation ensures that these are dealt with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes BCSR accesses in the board setup/reset code. The registers are
actually 16-bit, and their addresses are different between DBAu1550 and
other DBAu1xx0 boards.
From Sergei Shtylylov <sshtylyov@ru.mvista.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rdhwr emulation accidentally swallowed the SIGILL from most other
illegal instructions. Make sure to return -EFAULT by default.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Check if IRQ is disabled or in progress before reenabling interrupts
in jmr3927_irq_end..
o s/spinlock_irqsave/spin_lock_irqsave/
o s/spinlock_irqrestore/spin_unlock_irqrestore/
o Flush write buffer after setting IRQ mask
o In 2.6 jmr3927_ioc_interrupt interrupt handlers return irqreturn_t
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are currently two IPW_DEBUG options in drivers/net/wireless/Kconfig
(one for ipw2100 and one for ipw2200). The attached patch splits it into
IPW2100_DEBUG and IPW2200_DEBUG.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: "James P. Ketrenos" <ipw2100-admin@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Use kzalloc for IPW2200
- Fix config dependency for IPW2200
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Thanks to LinuxICC (http://linuxicc.sf.net), a comparison of a u32 less
than 0 was found, this patch changes the variable to a signed int so that
comparison is meaningful.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Added a more verbose entry for the 'ondemend' governor and an entry for the
'conservative' governor to the documentation.
Signed-off-by: Alexander Clouter <alex-kernel@digriz.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The use of the 'ignore_nice' sysfs file is confusing to anyone using it.
This removes the sysfs file 'ignore_nice' and in its place creates a
'ignore_nice_load' entry that defaults to '0'; meaning nice'd processes
_are_ counted towards the 'business' calculation.
WARNING: this obvious breaks any userland tools that expected ignore_nice'
to exist, to draw attention to this fact it was concluded on the mailing
list that the entry should be removed altogether so the userland app breaks
and so the author can build simple to detect workaround. Having said that
it seems currently very few tools even make use of this functionality; all
I could find was a Gentoo Wiki entry.
Signed-off-by: Alexander Clouter <alex-kernel@digriz.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Hello Jeff,
this patch changes causes the airo driver to not reset the card when a
temporary WEP key is set, when the IW_ENCODE_TEMP flag is used. This is
needed for xsupplicant as 802.1x, LEAP, etc. change WEP keys frequently
after authentication and resetting the card causes infinite
reauthentication.
Javier and Jean agree with the patch, Javier suggested I send this to
you, can you apply this?
Thanks.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
without this patch after an rmmod, modprobe the card won't work anymore
until the next reboot.
This patch seem safe to apply for all cards as the bsd driver already do
that.
I had to add a timeout because strange things happen (issuecommand will
fail) if the card is already reseted (after a reboot).
PS : it seems there are missing reset when leaving monitor mode...
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Hi,
the patch below marks several libata (and libata-driver) structures
const so that they end up in the .rodata segment and don't false-share
cachelines with things that get dirtied often.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Power management parameters could not be set by iwconfig due to
incorrect error handling.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use platform_driver_unregister not driver_unregister to unregister a
struct platform_driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Disable/enable the SERDES carrier when an interface is administratively
downed/upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement pm3386 reset. A reset zeroes out the internally stored MAC
addresses, so we need to save and reload them by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a pm3386 hook for disabling/enabling the SERDES carrier, so that
we can disable it when the interface is administratively downed, and
enable it when it is upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When we reset the pm3386, it loses its internally stored MAC addresses
that were programmed into it by the bootloader (and are used by the
hardware for the generation of PAUSE frames.) Add a hook to allow
setting these addresses so that we can program them back by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After initialising, report the MAC address that we're using for
each port.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We assign nds[i] to a local variable 'dev', which we never use
afterwards. Use the local variable instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Even after an interface has gone !netif_running(), we still want to
catch the 'carrier went down' event for our internal bookkeeping.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sky2 driver introduced netif_rx_schedule_test(). This is
exactly what we need, so remove our local version of this function
(which was called netif_rx_schedule_prep_notup) and use the generic
one instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make caleb.c and pm3386.c include their own header files, to catch
incorrect prototype definitions.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove a number of unnecessary udelay() calls.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not register our netdevices with the kernel until we've actually
finished setting up the hardware and microcode.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes graceful stop timeout handling in PPC4xx EMAC driver.
Currently, when we stop TX/RX channels we just do some number of loops
without relying on actual spent time. This has finally bitten me on
one of our systems (heavy network traffic during start up, RX channel
is stopped several times to configure multicast list).
Graceful channel stop can take up to 1 frame time, so I've added
device specific timeout counter which depends on current link speed
and calls to udelay() to really wait required amount of time before
giving up.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove device specific proc interface. It doesn't handle
renames correctly; it ain't worth fixing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Shrink size of per device data by removing redundant fields
or things that are only used at boot up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allow control of checksumming parameters via ethtool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
