The SCLP base driver defines a new notifier call back for all upper level SCLP
drivers, like the SCLP console, etc. This guarantees that in suspend first the
upper level drivers are suspended and afterwards the SCLP base driver. For
resume it is the other way round. The SCLP base driver itself registers a
new platform device at the platform bus and gets PM notifications via
the dev_pm_ops.
In suspend, the SCLP base driver switches off the receiver and sender mask
This is done in sclp_deactivate(). After suspend all new requests will be
rejected with -EIO and no more interrupts will be received, because the masks
are switched off. For resume the sender and receiver masks are reset in
the sclp_reactivate() function.
When the SCLP console is suspended, all new messages are cached in the
sclp console buffers. In resume, all the cached messages are written to the
console. In addition to that we have an early resume function that removes
the cached messages from the suspend image.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements suspend/hibernation for the vmwatchdog driver. The
pm_notifier_callchain is used to get control on PM events. Since watchdog
operation and suspend cannot work together in a reliable fashion, the open
flag is also used to prevent suspend and open from happening at the same
time.
The watchdog can also be active with no open file descriptor. This patch
adds another flag which is only changed in vmwdt_keep_alive and
vmwdt_disable.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the 3215 console. On suspend
the console buffer is flushed to the 3215 device to have an empty console
buffer. Printks done while the 3215 device is suspended are buffered in
the 64K buffer of the 3215 device. If the buffer is full new messages will
push out the oldest messages to make room for the most recent message.
On resume the buffered messages are printed. If the system panics before
the 3215 device is resumed ccw_device_force_console is used to get the
console working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If something goes wrong in a suspend / resume cycle a ccw based console
if very likely in the suspended state and cannot print anything.
Introduce ccw_device_force_console to force the wake up of the console
device to be able to print the oops message. The console device drivers
should use this function only if the system paniced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following build failure caused by make allyesconfig using
CONFIG_HIBERNATION and CONFIG_DEBUG_PAGEALLOC
kernel/built-in.o: In function `saveable_page':
kernel/power/snapshot.c:897: undefined reference to `kernel_page_present'
kernel/built-in.o: In function `safe_copy_page':
kernel/power/snapshot.c:948: undefined reference to `kernel_page_present'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Hans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the dasd driver. On suspend
the dasd devices are stopped and removed from the focus of alias
management.
On resume they are reinitialized by rereading the device characteristics
and adding the device to the alias management.
In case the device has gone away during suspend it will caught in the
suspend state with stopped flag set to UNRESUMED. After it appears again
the restore function is called again.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prefetch instructions can generate spurious faults on certain
models of older CPUs. The faults themselves cannot be stopped
and they can occur pretty much anywhere - so the way we solve
them is that we detect certain patterns and ignore the fault.
There is one small path of code where we must not take faults
though: the #PF handler execution leading up to the reading
of the CR2 (the faulting address). If we take a fault there
then we destroy the CR2 value (with that of the prefetching
instruction's) and possibly mishandle user-space or
kernel-space pagefaults.
It turns out that in current upstream we do exactly that:
prefetchw(&mm->mmap_sem);
/* Get the faulting address: */
address = read_cr2();
This is not good.
So turn around the order: first read the cr2 then prefetch
the lock address. Reading cr2 is plenty fast (2 cycles) so
delaying the prefetch by this amount shouldnt be a big issue
performance-wise.
[ And this might explain a mystery fault.c warning that sometimes
occurs on one an old AMD/Semptron based test-system i have -
which does have such prefetch problems. ]
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
LKML-Reference: <20090616030522.GA22162@Krystal>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that enable_iommus() will call iommu_disable() for each iommu,
the call to disable_iommus() during resume is redundant. Also, the order
for an invalidation is to invalidate device table entries first, then
domain translations.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Clock function was changed, but highlander used old function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the flex_bdry setting for module vs. built-in
configuration of OneNAND.
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Signed-off-by: Vishak G <vishak.g@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maintain two flows, one for pow2 chunk sizes (which uses masks and
shift), and a flow for the general case (which uses sector_div).
This is for the sake of performance.
- introduce map_sector and is_io_in_chunk_boundary to encapsulate
those two flows better for raid0_make_request
- fix blk_mergeable to support the two flows.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
Remove chunk size check from md as this is now performed in the run
function in each personality.
Replace chunk size power 2 code calculations by a regular division.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
have raid0 check chunk size in run method instead of in md.
This is part of a series moving the checks from common code to
the personalities where they belong.
hardsect is short and chunksize is an int, so it is safe to use %.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
Replace the linear search with binary search in which_dev.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove num_sectors from dev_info and replace start_sector with
end_sector. This makes a lot of comparisons much simpler.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Get rid of sector_div and hash table for linear raid and replace
with a linear search in which_dev.
The hash table adds a lot of complexity for little if any gain.
Ultimately a binary search will be used which will have smaller
cache foot print, a similar number of memory access, and no
divisions.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
This setting doesn't seem to make sense (half the chunk size??) and
shouldn't be needed.
The segment boundary exported by raid0 should simply be the minimum
of the segment boundary of all component devices. And we already
get that right.
Signed-off-by: NeilBrown <neilb@suse.de>
If we treat conf->devlist more like a 2 dimensional array,
we can get the devlist for a particular zone simply by indexing
that array, so we don't need to store the pointers to subarrays
in strip_zone. This makes strip_zone smaller and so (hopefully)
searches faster.
Signed-of-by: NeilBrown <neilb@suse.de>
storing ->sectors is redundant as is can be computed from the
difference z->zone_end - (z-1)->zone_end
The one place where it is used, it is just as efficient to use
a zone_end value instead.
And removing it makes strip_zone smaller, so they array of these that
is searched on every request has a better chance to say in cache.
So discard the field and get the value from elsewhere.
Signed-off-by: NeilBrown <neilb@suse.de>
raid0_stop() removes all references to the raid0 configuration but
misses to free the ->devlist buffer.
This patch closes this leak, removes a pointless initialization and
fixes a coding style issue in raid0_stop().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the raid0 configuration is allocated in raid0_run() while
the buffers for the strip_zone and the dev_list arrays are allocated
in create_strip_zones(). On errors, all three buffers are freed
in raid0_run().
It's easier and more readable to do the allocation and cleanup within
a single function. So move that code into create_strip_zones().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently raid0_run() always returns -ENOMEM on errors. This is
incorrect as running the array might fail for other reasons, for
example because not all component devices were available.
This patch changes create_strip_zones() so that it returns a proper
error code (either -ENOMEM or -EINVAL) rather than 1 on errors and
makes raid0_run(), its single caller, return that value instead
of -ENOMEM.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The "sector_shift" and "spacing" fields of struct raid0_private_data
were only used for the hash table lookups. So the removal of the
hash table allows get rid of these fields as well which simplifies
create_strip_zones() and raid0_run() quite a bit.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The raid0 hash table has become unused due to the changes in the
previous patch. This patch removes the hash table allocation and
setup code and kills the hash_table field of struct raid0_private_data.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
1/ remove current_start. The same value is available in
zone->dev_start and storing it separately doesn't gain anything.
2/ rename curr_zone_start to curr_zone_end as we are now more
focused on the 'end' of each zone. We end up storing the
same number though - the old name was a little confusing
(and what does 'current' mean in this context anyway).
Signed-off-by: NeilBrown <neilb@suse.de>
eec9462088 fold mg_disk.h into mg_disk.c,
but mg_disk platform driver needs private data for operation. This also
make mg_disk.c as machine independent. Seperate only needed structure and
defines to mg_disk.h
Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
DM reuses the request queue when swapping in a new device table
Introduce blk_set_default_limits() which can be used to reset the the
queue_limits prior to stacking devices.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
I noticed a blank line in blktrace output. This patch fixes that.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
