Add the vbus_draw() callback to inform the transceiver, if
it exists, how much current may be drawn. The decision is
taken on gadget driver side using the configuration chosen
by the host and its bMaxPower field. Some systems can use
the host's VBUS supply to augment or recharge a battery.
(There's also a default of 100 mA for unconfigured devices,
or 8 mA if they're OTG devices.)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a transceiver driver is used, no automatic udc enable
is done. The transceiver (OTG or not) should :
- take care of VBus sensing
- call usb_gadget_vbus_connect()
- call usb_gadget_vbus_disconnect()
The pullup should remain within this driver's management,
either by gpio_pullup of udc_command() fields.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.
It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.
[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Phil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.
The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that. We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.
(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial error path leak fix. Problem found by Daniel Marjamäki using
cppcheck
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Should be using strncmp as the data from user space may be unterminated
(Bug #8004)
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes two problems in the claw driver identified by
static code analysis:
o Change in case differentiation of received sense codes
o Use correct data length in claw hard_start_xmit routine
Signed-off-by: Andrew H. Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ursula Braun <ursula.braun@de.ibm.com>
This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Pass pointer to buffer for IDENTIFY data to do_identify()
and try_to_identify().
* Un-static try_to_identify() and use it in ide_driveid_update().
* Rename try_to_identify() to ide_dev_read_id().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear drive IRQ after re-enabling local IRQs in ide_driveid_update()
to match try_to_identify().
Also remove superfluous local_irq_enable() call while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Defer classifying device type from do_identify() to do_probe().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
do_identify() marks EXABYTENEST device as non-present and frees
drive->id so enable_nest() has absolutely no chance of working.
The code was like this since at least 2.6.12-rc2 and nobody
has noticed so just remove broken EXABYTENEST support.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Doing kmalloc() in the middle of command execution is not only ugly
but leaves drive waiting to send data on kmalloc() failure. Fix it.
While at it:
* Unify error code paths.
* Fixup error message to be more useful and add missing KERN_ERR level.
* Rename 'stat' variable to 's'.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous <asm/intctl-regs.h> include.
* Remove no longer used SUPPORT_SLOW_DATA_PORTS define.
* Move defining SUPPORT_VLB_SYNC to <linux/ide.h>.
* Use __ide_mm_*() macros from <asm-generic/ide_iops.h>
(MN10300 uses only memory-mapped I/O).
* Remove <asm/ide.h>.
While at it:
* Remove superfluous SPARC64 #ifdef from <linux/ide.h>.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set ->irq explicitly in cs5520.c.
* Remove irq argument from ide_hw_configure().
* Remove pciirq argument from ide_pci_setup_ports().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return 0 instead of dev->irq in ->init_chipset implementations.
* Fix ->init_chipset method to return 'int' value instead of
'unsigned int' one.
This fixes ->init_chipset handling for host drivers (cs5530, hpt366
and pdc202xx_new) for which it is possible for this method to fail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is now handled by core IDE PCI code.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move handling of IDE_HFLAG[_FORCE]_LEGACY_IRQS from ide_init_port()
to ide_pci_init_{one,two}().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ->init_hwif to check if IDE PCI controller is in compatibility
mode instead of checking for hwif->irq == 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add missing pci_get_legacy_ide_irq() implementation
before it becomes required by core IDE PCI code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do some CodingStyle fixups in <linux/ide.h> while at it.
v2:
Add missing <linux/delay.h> include (reported by Stephen Rothwell).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix following checkpatch.pl warnings/errors:
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
- WARNING: line over 80 characters
- ERROR: trailing whitespace
- ERROR: space required before the open parenthesis '('
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
