When running a 31-bit ptrace, on either an s390 or s390x kernel,
reads and writes into a padding area in struct user_regs_struct32
will result in a kernel panic.
This is also known as CVE-2008-1514.
Test case available here:
http://sources.redhat.com/cgi-bin/cvsweb.cgi/~checkout~/tests/ptrace-tests/tests/user-area-padding.c?cvsroot=systemtap
Steps to reproduce:
1) wget the above
2) gcc -o user-area-padding-31bit user-area-padding.c -Wall -ggdb2 -D_GNU_SOURCE -m31
3) ./user-area-padding-31bit
<panic>
Test status
-----------
Without patch, both s390 and s390x kernels panic. With patch, the test case,
as well as the gdb testsuite, pass without incident, padding area reads
returning zero, writes ignored.
Nb: original version returned -EINVAL on write attempts, which broke the
gdb test and made the test case slightly unhappy, Jan Kratochvil suggested
the change to return 0 on write attempts.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds DMA support for Freescale i.MX27 SoCs. It is derived
from the i.MX1 port and should (though currently untested) still be
working for the i.MX1.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Drivers which are going to use it will have to select it and use
imx_set_irq_fiq() to set FIQ mode for this interrupt.
Changes since V1:
- removed '#ifdef CONFIG_FIQ' from irqs.h
- renamed imx_set_irq_type() to imx_set_irq_fiq()
- made irqt unsigned
- fixed irq number check
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix some base address declaration by adding a cast.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This one adds definitions to configure RTCK pad (PE16) in primary and alternate
function. The RTCK Pin is used by one wire master controller and as JTAG Clock
return.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds macros to get CSCR upper, lower and additional registers.
These registers are needed to configure a chip select line. The offset
layouts of these Registers are identical on mx27 and mx31, hence we can
use the macros in generic way
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this adds convenience values usable by mxc_iomux_mode() to configure Pins of the
spi interfaces on mx31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Needed for 8250 serial port and CS89x0 ethernet interface.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Changed the mux naming scheme from "IEC9258 Mux" to "IEC958 Playback Source" to match
the coding style.
Signed-by-off: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added slave_dig_outs entries for several IDT codecs that have multiple
SPDIF outs, and enabled these SPDIF outs in several pin configs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Muting the DAC masks artefacts introduced as the digital stream shuts
down, for example when the input stops being clocked.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hopefully this will make merges a little bit easier.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for playing a stream on multiple digital outs. This is done
by defining codec->slave_dig_outs as array of hda_nid_t with a null-terminated entry to set the
slave SPDIF outs, in which the slave outs have cloned settings of the master out (e.g. dig_out_nid).
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The __exit cleanup_oss_soundcore() is called from
the __init init_soundcore(). This causes section mismatch
and breaks kernel's linking on sparc64.
Remove the __exit attribute from the cleanup_oss_soundcore().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The lock used in snd_ctl_dev_disconnect() should be card->ctl_files_rwlock
for protection of card->ctl_files entries, instead of card->controls_rwsem.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Inspired by Alexander Beregalov's patches for wtm and aureon.c,
I decided to run checkpatch on some more files. After some work
checkpatch.pl-0.23 --no-tree --file --strict <file> reports
0 errors, 0 warnings, 0 checks, n lines checked for:
phase.c
phase.h
juli.c (1 check about unused code, maybe we should comment it)
juli.h (no changes necessary)
In other files I have just fixed // comments and long lines along the
way (but not all of them), more coming up.
Signed-off-by: Vedran Miletic <rivanvx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dynamically create mux controls for SPDIF outs on certain IDT/Sigmatel codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
before:
total: 304 errors, 137 warnings, 2259 lines checked
after:
total: 0 errors, 121 warnings, 2284 lines checked
Compile tested, size is different because of include was changed,
but without that change md5sum is different because of cmp cx,dx/cmp
dx,cx swap and __LINE__ was changed in printk function.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
[Additional coding standards fixes by Mark Brown.]
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
[Additional coding standards fixes by Mark Brown.]
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
SPORT is a serial port which can support serveral serial communication
protocols. It can be used as I2C/PCM/AC97. For further information,
please look up the HRM.
[Additional coding standards fixes by Mark Brown.]
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
[Some checkpatch fixups done by Mark Brown.]
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert the wm8510 codec driver to the new (standard) device
driver binding model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Geoffrey Wossum <gwossum@acm.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert the lm4857 driver in neo1973_wm8753 to the new (standard)
i2c device driver binding model. I assumed that the LM4857 was always
on the same I2C bus as the WM8753 codec.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Tim Niemeyer <reddog@mastersword.de>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert the wm8753 codec driver to the new (standard) i2c device
driver binding model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The error handling in neo1973_init is incorrect:
* If platform_device_add fails, we go on with the rest of the
initialization instead of bailing out. Things will break when the
module is removed (platform_device_unregister called on a device
that wasn't registered.)
* If i2c_add_driver fails, we return an error so the module will not
load, but we don't unregister neo1973_snd_device, so we are leaking
resources.
Add the missing error handling.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Tim Niemeyer <reddog@mastersword.de>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove the Kconfig definitions of unused variables AEDSP16_MSS and
AEDSP16_SBPRO since they're:
1) unused, and
2) referenced incorrectly anyway.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Empty files remained likely due to wrong patching.
Remove them now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow probing of 4 codecs on known good situations.
On some known bad situations, it should be avoided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
