In ext2_rename(), dir_page is acquired through ext2_dotdot(). It is
then released through ext2_set_link() but only if old_dir != new_dir.
Failing that, the pkmap reference count is never decremented and the
page remains pinned forever. Repeat that a couple times with highmem
pages and all pkmap slots get exhausted, and every further kmap() calls
end up stalling on the pkmap_map_wait queue at which point the whole
system comes to a halt.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: ocfs2_write_begin_nolock() should handle len=0
ocfs2: invalidate dentry if its dentry_lock isn't initialized.
The whole write-room thing is something that is up to the _caller_ to
worry about, not the pty layer itself. The total buffer space will
still be limited by the buffering routines themselves, so there is no
advantage or need in having pty_write() artificially limit the size
somehow.
And what happened was that the caller (the n_tty line discipline, in
this case) may have verified that there is room for 2 bytes to be
written (for NL -> CRNL expansion), and it used to then do those writes
as two single-byte writes. And if the first byte written (CR) then
caused a new tty buffer to be allocated, pty_space() may have returned
zero when trying to write the second byte (LF), and then incorrectly
failed the write - leading to a lost newline character.
This should finally fix
http://bugzilla.kernel.org/show_bug.cgi?id=14015
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When translating CR to CRNL in the n_tty line discipline, we did it as
two tty_put_char() calls. Which works, but is stupid, and has caused
problems before too with bad interactions with the write_room() logic.
The generic USB serial driver had that problem, for example.
Now the pty layer had similar issues after being moved to the generic
tty buffering code (in commit d945cb9cce:
"pty: Rework the pty layer to use the normal buffering logic").
So stop doing the silly separate two writes, and do it as a single write
instead. That's what the n_tty layer already does for the space
expansion of tabs (XTABS), and it means that we'll now always have just
a single write for the CRNL to match the single 'tty_write_room()' test,
which hopefully means that the next time somebody screws up buffering,
it won't cause weeks of debugging.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tom Horsley reports that his debugger hangs when it tries to read
/proc/pid_of_tracee/maps, this happens since
"mm_for_maps: take ->cred_guard_mutex to fix the race with exec"
04b836cbf19e885f8366bccb2e4b0474346c02d
commit in 2.6.31.
But the root of the problem lies in the fact that do_execve() path calls
tracehook_report_exec() which can stop if the tracer sets PT_TRACE_EXEC.
The tracee must not sleep in TASK_TRACED holding this mutex. Even if we
remove ->cred_guard_mutex from mm_for_maps() and proc_pid_attr_write(),
another task doing PTRACE_ATTACH should not hang until it is killed or the
tracee resumes.
With this patch do_execve() does not use ->cred_guard_mutex directly and
we do not hold it throughout, instead:
- introduce prepare_bprm_creds() helper, it locks the mutex
and calls prepare_exec_creds() to initialize bprm->cred.
- install_exec_creds() drops the mutex after commit_creds(),
and thus before tracehook_report_exec()->ptrace_stop().
or, if exec fails,
free_bprm() drops this mutex when bprm->cred != NULL which
indicates install_exec_creds() was not called.
Reported-by: Tom Horsley <tom.horsley@att.net>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On low-memory systems, anti-fragmentation gets disabled as fragmentation
cannot be avoided on a sufficiently large boundary to be worthwhile. Once
disabled, there is a period of time when all the pageblocks are marked
MOVABLE and the expectation is that they get marked UNMOVABLE at each call
to __rmqueue_fallback().
However, when MAX_ORDER is large the pageblocks do not change ownership
because the normal criteria are not met. This has the effect of
prematurely breaking up too many large contiguous blocks. This is most
serious on NOMMU systems which depend on high-order allocations to boot.
This patch causes pageblocks to change ownership on every fallback when
anti-fragmentation is disabled. This prevents the large blocks being
prematurely broken up.
This is a fix to commit 49255c619f [page
allocator: move check for disabled anti-fragmentation out of fastpath] and
the problem affects 2.6.31-rc8.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the error handling in do_mmap_pgoff(). If do_mmap_shared_file() or
do_mmap_private() fail, we jump to the error_put_region label at which
point we cann __put_nommu_region() on the region - but we haven't yet
added the region to the tree, and so __put_nommu_region() may BUG
because the region tree is empty or it may corrupt the region tree.
To get around this, we can afford to add the region to the region tree
before calling do_mmap_shared_file() or do_mmap_private() as we keep
nommu_region_sem write-locked, so no-one can race with us by seeing a
transient region.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cancel_delayed_work() has to use del_timer_sync() to guarantee the timer
function is not running after return. But most users doesn't actually
need this, and del_timer_sync() has problems: it is not useable from
interrupt, and it depends on every lock which could be taken from irq.
Introduce __cancel_delayed_work() which calls del_timer() instead.
The immediate reason for this patch is
http://bugzilla.kernel.org/show_bug.cgi?id=13757
but hopefully this helper makes sense anyway.
As for 13757 bug, actually we need requeue_delayed_work(), but its
semantics are not yet clear.
Merge this patch early to resolves cross-tree interdependencies between
input and infiniband.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a target writes invalid status (typically status of a command that
already timed out), firewire-sbp2 attempts to put away an ORB that
doesn't exist. https://bugzilla.redhat.com/show_bug.cgi?id=519772
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In dual-buffer DMA mode, no video frames are ever received from R5C832
by libdc1394. Fallback to packet-per-buffer DMA works reliably.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/13393/focus=13476
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
An Agere FW643 OHCI 1.1 card works fine for video reception from one
camera but fails early if receiving from two cameras. After a short
while, no IR IRQ events occur and the context control register does not
react anymore. This happens regardless whether both IR DMA contexts are
dual-buffer or one is dual-buffer and the other packet-per-buffer.
This can be worked around by disabling dual buffer DMA mode entirely.
http://sourceforge.net/mailarchive/message.php?msg_name=4A7C0594.2020208%40gmail.com
(Reported by Samuel Audet.)
In another report (by Jonathan Cameron), an FW643 works OK with two
cameras in dual buffer mode. Whether this is due to different chip
revisions or different usage patterns (different video formats) is not
yet clear. However, as far as the current capabilities of
firewire-core's isochronous I/O interface are concerned, simply
switching off dual-buffer on non-working and working FW643s alike is not
a problem in practice. We only need to revisit this issue if we are
going to enhance the interface, e.g. so that applications can explicitly
choose modes.
Reported-by: Samuel Audet <samuel.audet@gmail.com>
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This fixes a regression due to post 2.6.30 commit "firewire: core: do
not DMA-map stack addresses" 6fdc037094.
As David Moore noted, a previously correct sizeof() expression became
wrong since the commit changed its argument from an array to a pointer.
This resulted in an oops in ohci_cancel_packet in the shared workqueue
thread's context when an isochronous resource was to be freed.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If the parent qdisc doesn't support classes, use EOPNOTSUPP.
If the parent class doesn't exist, use ENOENT. Currently EINVAL
is returned in both cases.
Additionally check whether grafting is supported and remove a now
unnecessary graft function from sch_ingress.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC net/netlink/genetlink.o
net/netlink/genetlink.c: In function ‘genl_register_mc_group’:
net/netlink/genetlink.c:139: warning: ‘err’ may be used uninitialized in this function
From following the code 'err' is initialized, but set it to zero to
silence the warning.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the ability to swap the cpu buffers adds a small overhead to
the recording of a trace, we only want to add it when needed.
Only the irqsoff and preemptoff tracers use this feature, and both are
not recommended for production kernels. This patch disables its use
when neither irqsoff nor preemptoff is configured.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Because the irqsoff tracer can swap an internal CPU buffer, it is possible
that a swap happens between the start of the write and before the committing
bit is set (the committing bit will disable swapping).
This patch adds a check for this and will fail the write if it detects it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The irqsoff tracer will fail to swap the cpu buffer with the max
buffer if it preempts a commit. Instead of ignoring this, this patch
makes the tracer report it if the last max latency failed due to preempting
a current commit.
The output of the latency tracer will look like this:
# tracer: irqsoff
#
# irqsoff latency trace v1.1.5 on 2.6.31-rc5
# --------------------------------------------------------------------
# latency: 112 us, #1/1, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 #P:4)
# -----------------
# | task: -4281 (uid:0 nice:0 policy:0 rt_prio:0)
# -----------------
# => started at: save_args
# => ended at: __do_softirq
#
#
# _------=> CPU#
# / _-----=> irqs-off
# | / _----=> need-resched
# || / _---=> hardirq/softirq
# ||| / _--=> preempt-depth
# |||| /
# ||||| delay
# cmd pid ||||| time | caller
# \ / ||||| \ | /
bash-4281 1d.s6 265us : update_max_tr_single: Failed to swap buffers due to commit in progress
Note the latency time and the functions that disabled the irqs or preemption
will still be listed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds a trace_array_printk to allow a tracer to use the
trace_printk on its own trace array.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The latency tracers (irqsoff and wakeup) can swap trace buffers
on the fly. If an event is happening and has reserved data on one of
the buffers, and the latency tracer swaps the global buffer with the
max buffer, the result is that the event may commit the data to the
wrong buffer.
This patch changes the API to the trace recording to be recieve the
buffer that was used to reserve a commit. Then this buffer can be passed
in to the commit.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reseting the trace buffer without first disabling the buffer and
waiting for any writers to complete, can corrupt the ring buffer.
This patch makes the external version of tracing_reset safe from
corruption by disabling the ring buffer and calling synchronize_sched.
This version can no longer be called from interrupt context. But all those
callers have been removed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently the latency tracers reset the ring buffer. Unfortunately
if a commit is in process (due to a trace event), this can corrupt
the ring buffer. When this happens, the ring buffer will detect
the corruption and then permanently disable the ring buffer.
The bug does not crash the system, but it does prevent further tracing
after the bug is hit.
Instead of reseting the trace buffers, the timestamp of the start of
the trace is used instead. The buffers will still contain the previous
data, but the output will not count any data that is before the
timestamp of the trace.
Note, this only affects the static trace output (trace) and not the
runtime trace output (trace_pipe). The runtime trace output does not
make sense for the latency tracers anyway.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Since our TSN map is capable of holding at most a 4K chunk gap,
there is no way that during this gap, a stream sequence number
(unsigned short) can wrap such that the new number is smaller
then the next expected one. If such a case is encountered,
this is a protocol violation.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This shrinks the size of struct sctp_association a little.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.
In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.
This sysctl configuration allows SCTP to function in such
unconventional networking environments.
Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack
Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We used to perform 2 routing lookups for a new transport: one
just for path mtu detection, and one to actually route to destination
and path mtu update when sending a packet. There is no point in doing
both of them, especially since the first one just for path mtu doesn't
take into account source address and sometimes gives the wrong route,
causing path mtu updates anyway.
We now do just the one call to do both route to destination and get
path mtu updates.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We currently track if AUTH has been bundled using the 'auth'
pointer to the chunk. However, AUTH is disallowed after DATA
is already in the packet, so we need to instead use the
'has_auth' field.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
The packet information does not reset after packet transmit, this
may cause some problems such as following DATA chunk be sent without
AUTH chunk, even if the authentication of DATA chunk has been
requested by the peer.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Add-IP feature allows users to delete an active transport. If that
transport has chunks in flight, those chunks need to be moved to another
transport or association may get into unrecoverable state.
Reported-by: Rafael Laufer <rlaufer@cisco.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We had a bug that we never stored the user-defined value for
MAXSEG when setting the value on an association. Thus future
PMTU events ended up re-writing the frag point and increasing
it past user limit. Additionally, when setting the option on
the socket/endpoint, we effect all current associations, which
is against spec.
Now, we store the user 'maxseg' value along with the computed
'frag_point'. We inherit 'maxseg' from the socket at association
creation and use it as an upper limit for 'frag_point' when its
set.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
SCTP will delay the last part of a large write due to NAGLE, if that
part is smaller then MTU. Since we are doing large writes, we might
as well send the last portion now instead of waiting untill the next
large write happens. The small portion will be sent as is regardless,
so it's better to not delay it.
This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com>
and Doug Graham <dgraham@nortel.com>. Many thanks go out to them.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
The decision to delay due to Nagle should be based on the path mtu
and future packet size. We currently incorrectly base it on
'frag_point' which is the SCTP DATA segment size, and also we do
not count DATA chunk header overhead in the computation. This
actuall allows situations where a user can set low 'frag_point',
and then send small messages without delay.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We currently set a_rwnd to 0 when faking a SACK from SHUTDOWN.
This results in an hung association if the remote only uses
SHUTDOWNs (which it's allowed to do) to acknowlege DATA when
closing. The reason for that is that we simply honor the a_rwnd
from the sack, but since we faked it to be 0, we enter 0-window
probing. The fix is to use the peers old rwnd and add our flight
size to it.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
SCTP has a problem that when small chunks are used, it is possible
to exhaust the receiver buffer without fully closing receive window.
This happens due to all overhead that we have account for with small
messages. To fix this, when receive buffer is exceeded, we'll drop
the window to 0 and save the 'drop' portion. When application starts
reading data and freeing up recevie buffer space, we'll wait until
we've reached the 'drop' window and then add back this 'drop' one
mtu at a time. This worked well in testing and under stress produced
rather even recovery.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
If T3 timer expires, we are retransmitting data due to timeout any
any fast recovery is null and void. We can clear the fast recovery
flag.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
SCTP RFC 4960 states that unacknowledged HEARTBEATS count as
errors agains a given transport or endpoint. As such, we
should increment the error counts for only for unacknowledged
HB, otherwise we detect failure too soon. This goes for both
the overall error count and the path error count.
Now, there is a difference in how the detection is done
between the two. The path error detection is done after
the increment, so to detect it properly, we actually need
to exceed the path threshold. The overall error detection
is done _BEFORE_ the increment. Thus to detect the failure,
it's enough for the error count to match the threshold.
This is why all the state functions use '>=' to detect failure,
while path detection uses '>'.
Thanks goes to Chunbo Luo <chunbo.luo@windriver.com> who first
proposed patches to fix this issue and made me re-read the spec
and the code to figure out how this cruft really works.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
The receiver of the HEARTBEAT should respond with a HEARTBEAT ACK
that contains the Heartbeat Information field copied from the
received HEARTBEAT chunk. So the received HEARTBEAT-ACK chunk
must have a length of:
sizeof(sctp_chunkhdr_t) + sizeof(sctp_sender_hb_info_t)
A badly formatted HB-ACK chunk, it is possible that we may access
invalid memory. We should really make sure that the chunk format
is what we expect, before attempting to touch the data.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
If Cumulative TSN Ack field of SHUTDOWN chunk is less than the
Cumulative TSN Ack Point then drop the SHUTDOWN chunk.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself. This means
that for each fragment we go all the way down the stack
and back up. This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).
We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine. The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
If the association has a SACK timer pending and now DATA queued
to be send, we'll try to bundle the SACK with the next application send.
As such, try encourage bundling by accounting for SACK in the size
of the first chunk fragment.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We are now trying to bundle SACKs when we have outbound
DATA to send. However, there are situations where this
outbound DATA will not be sent (due to congestion or
available window). In such cases it's ok to wait for the
timer to expire. This patch refactors the sending code
so that betfore attempting to bundle the SACK we check
to see if the DATA will actually be transmitted.
Based on eirlier works for Doug Graham <dgraham@nortel.com> and
Wei Youngjun <yjwei@cn.fujitsu.com>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Since an application may specify the maximum SCTP fragment size
that all data should be fragmented to, we need to fix how
we do segmentation. Right now, if a user specifies a small
fragment size, the segment size can go negative in the presence
of AUTH or COOKIE_ECHO bundling.
What we need to do is track the largest possbile DATA chunk that
can fit into the mtu. Then if the fragment size specified is
bigger then this maximum length, we'll shrink it down. Otherwise,
we just use the smaller segment size without changing it further.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down. If this was a result of a close() call, there will be no socket
and will cause a memory leak. We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch corrects the conditions under which a SACK will be piggybacked
on a DATA packet. The previous condition was incorrect due to a
misinterpretation of RFC 4960 and/or RFC 2960. Specifically, the
following paragraph from section 6.2 had not been implemented correctly:
Before an endpoint transmits a DATA chunk, if any received DATA
chunks have not been acknowledged (e.g., due to delayed ack), the
sender should create a SACK and bundle it with the outbound DATA
chunk, as long as the size of the final SCTP packet does not exceed
the current MTU. See Section 6.2.
When about to send a DATA chunk, the code now checks to see if the SACK
timer is running. If it is, we know we have a SACK to send to the
peer, so we append the SACK (assuming available space in the packet)
and turn off the timer. For a simple request-response scenario, this
will result in the SACK being bundled with the response, meaning the
the SACK is received quickly by the client, and also meaning that no
separate SACK packet needs to be sent by the server to acknowledge the
request. Prior to this patch, a separate SACK packet would have been
sent by the server SCTP only after its delayed-ACK timer had expired
(usually 200ms). This is wasteful of bandwidth, and can also have a
major negative impact on performance due the interaction of delayed ACKs
with the Nagle algorithm.
Signed-off-by: Doug Graham <dgraham@nortel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch removes an unused union definition (sctp_cmsg_data_t)
from include/net/sctp/user.h.
Signed-off-by: Rami Rosen <rosenrami@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When the sctp transport is marked down, we can release the
cached route and force a new lookup when attempting to use
this transport for anything. This way, if a better route
or source address is available, we'll try to use it.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
