Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix iounmap() of pass-through P4 addresses. Without this patch
iounmap() on the sh7780 rtc area results in a warning message.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for single IRQ hardware to the sh-rtc driver.
This is useful for processors with limited interrupt masking
support such as sh7750 and sh7780. With this patch in place we
can add logic to the intc code that merges all RTC vectors into
a single linux interrupt with proper masking/unmasking support.
Specify a single IRQ in the platform data to use this new shared
IRQ feature. Separate Periodic/Carry/Alarm IRQs are still supported.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the serial console code to wait for the transmit FIFO,
make sure all bits have been put on the wire before returning.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
- break out restore_regs() from restore_all()
- the register saving order is unchanged
- use restore_regs() in sh_bios_handler and restore_all
- document the function
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the maple bus to support asynchronous block reads
and writes as well as generally improving the quality of the code and
supporting concurrency (all needed to support the Dreamcast visual
memory unit - a driver will also be posted for that).
Changes in the bus driver necessitate some changes in the two maple bus
input drivers that are currently in mainline.
As well as supporting block reads and writes this code clean up removes
some poor handling of locks, uses an atomic status variable to serialise
access to devices and more robusly handles the general performance
problems of the bus.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
set on the next initialization (without a reboot inbetween).
This causes breakage on the second initialization due to code that
checks this bit (ssb_device_is_enabled() checks).
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.
This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
hp-plus needs to call __alloc_eip_netdev() instead of
__alloc_ei_netdev() since it is linked with 8390p.o.
Fixes this build error:
ERROR: "__alloc_ei_netdev" [drivers/net/hp-plus.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an outdated README for the flexcop-driver.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.
There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.
This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.
This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As explained in "Writing an ALSA driver" (T. Iwai), audio drivers should
set the struct device for the card before registering the card instance.
This will add the correct /sys/class/sound/cardN/device symlink, so HAL
can see the device and ConsoleKit sets its ACL permissions for the
logged-in user.
For em28xx audio capture cards found e.g. in Hauppauge WinTV-HVR-900 (R2),
this patch fixes errors like:
ALSA lib pcm_hw.c:1429:(_snd_pcm_hw_open) Invalid value for card
Error opening audio: Permission denied
when running mplayer as a normal user.
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: add IO error check in ocfs2_get_sector()
ocfs2: set gap to seperate entry and value when xattr in bucket
ocfs2: lock the metaecc process for xattr bucket
ocfs2: Use the right access_* method in ctime update of xattr.
ocfs2/dlm: Make dlm_assert_master_handler() kill itself instead of the asserter
ocfs2/dlm: Use ast_lock to protect ast_list
ocfs2: Cleanup the lockname print in dlmglue.c
ocfs2/dlm: Retract fix for race between purge and migrate
ocfs2: Access and dirty the buffer_head in mark_written.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: AMD 813x B2 devices do not need boot interrupt quirk
PCI: Enable PCIe AER only after checking firmware support
PCI: pciehp: Handle interrupts that happen during initialization.
PCI: don't enable too many HT MSI mappings
PCI: add some sysfs ABI docs
PCI quirk: enable MSI on 8132
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Turns out that the new AMD 813x devices do not need the
quirk_disable_amd_813x_boot_interrupt quirk to be run on them. If it
is, no interrupts are seen on the PCI-X adapter.
From: Stefan Assmann <sassmann@novell.com>
Reported-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Tested-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
The mesh and radiotap interfaces need to use the same private data as
the main wifi interface. If the main wifi interface uses netdev_priv(),
but the other interfaces ->ml_priv, there's no way to figure out where
the private data actually is in the WEXT handlers and netdevice
callbacks. So make everything use ->ml_priv.
Fixes botched netdev_priv() conversion introduced by "netdevice
libertas: Fix directly reference of netdev->priv", though admittedly
libertas' use of ->priv was somewhat "special".
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the obvious bugs have been worked out, specifically
the iwlagn issue, and the write buffer errata, DMAR should be safe
to turn back on by default. (We've had it on since those patches were
first written a few weeks ago, without any noticeable bug reports
(most have been due to the dma-api debug patchset.))
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We really don't want the BIOS flash mapping hacks to get automatically
loaded.
No idea why it isn't using pci_register_driver() though -- that should
be fine... and is even _present_ but disabled by #if 0.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch set a gap (4 bytes) between xattr entry and
name/value when xattr in bucket. This gap use to seperate
entry and name/value when a bucket is full. It had already
been set when xattr in inode/block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
For other metadata in ocfs2, metaecc is checked in ocfs2_read_blocks
with io_mutex held. While for xattr bucket, it is calculated by
the whole buckets. So we have to add a spin_lock to prevent multiple
processes calculating metaecc.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Tested-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
In ctime updating of xattr, it use the wrong type of access for
inode, so use ocfs2_journal_access_di instead.
Reported-and-Tested-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
In dlm_assert_master_handler(), if we get an incorrect assert master from a node
that, we reply with EINVAL asking the asserter to die. The problem is that an
assert is sent after so many hoops, it is invariably the node that thinks the
asserter is wrong, is actually wrong. So instead of killing the asserter, this
patch kills the assertee.
This patch papers over a race that is still being addressed.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
The code was using dlm->spinlock instead of dlm->ast_lock to protect the
ast_list. This patch fixes the issue.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
The dentry lock has a different format than other locks. This patch fixes
ocfs2_log_dlm_error() macro to make it print the dentry lock correctly.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Mainline commit d4f7e650e5 attempts to delay
the dlm_thread from sending the drop ref message if the lockres is being
migrated. The problem is that we make the dlm_thread wait for the migration
to complete. This causes a deadlock as dlm_thread also participates in the
lockres migration process.
A better fix for the original oss bugzilla#1012 is in testing.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
In __ocfs2_mark_extent_written, when we meet with the situation
of c_split_covers_rec, the old solution just replace the extent
record and forget to access and dirty the buffer_head. This will
cause a problem when the unwritten extent is in an extent block.
So access and dirty it.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
xen/blkfront: use blk_rq_map_sg to generate ring entries
block: reduce stack footprint of blk_recount_segments()
cciss: shorten 30s timeout on controller reset
block: add documentation for register_blkdev()
block: fix bogus gcc warning for uninitialized var usage
It needs to happen before any firewire driver actually registers itself,
and that was previously handled by having the Makefile list the core
ieee1394 files before the drivers.
But now there are firewire drivers in drivers/media, and the Makefile
games aren't enough. So just make ieee1394_init happen earlier in the
init sequence, the way all other bus layers already do.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Henrik Kurelid <henrik@kurelid.se>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ben Backx <ben@bbackx.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix incorrect condition check
No need to start rt bandwidth timer when rt bandwidth is disabled.
If this timer starts, it may stop at sched_rt_period_timer() on the first time.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We already have a valid net in that place, but this is not just a
cleanup - the tw pointer can be NULL there sometimes, thus causing
an oops in NET_NS=y case.
The same place in ipv4 code already works correctly using existing
net, rather than tw's one.
The bug exists since 2.6.27.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On occasion, the request will apparently have more segments than we
fit into the ring. Jens says:
> The second problem is that the block layer then appears to create one
> too many segments, but from the dump it has rq->nr_phys_segments ==
> BLKIF_MAX_SEGMENTS_PER_REQUEST. I suspect the latter is due to
> xen-blkfront not handling the merging on its own. It should check that
> the new page doesn't form part of the previous page. The
> rq_for_each_segment() iterates all single bits in the request, not dma
> segments. The "easiest" way to do this is to call blk_rq_map_sg() and
> then iterate the mapped sg list. That will give you what you are
> looking for.
> Here's a test patch, compiles but otherwise untested. I spent more
> time figuring out how to enable XEN than to code it up, so YMMV!
> Probably the sg list wants to be put inside the ring and only
> initialized on allocation, then you can get rid of the sg on stack and
> sg_init_table() loop call in the function. I'll leave that, and the
> testing, to you.
[Moved sg array into info structure, and initialize once. -J]
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add documentation for register_blkdev() function and for the parameters.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Newer gcc throw this warning:
fs/bio.c: In function ?bio_alloc_bioset?:
fs/bio.c:305: warning: ?p? may be used uninitialized in this function
since it cannot figure out that 'p' is only ever used if 'bs' is non-NULL.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the mandatory algorithm testing at registration, we have
now created a deadlock with algorithms requiring fallbacks.
This can happen if the module containing the algorithm requiring
fallback is loaded first, without the fallback module being loaded
first. The system will then try to test the new algorithm, find
that it needs to load a fallback, and then try to load that.
As both algorithms share the same module alias, it can attempt
to load the original algorithm again and block indefinitely.
As algorithms requiring fallbacks are a special case, we can fix
this by giving them a different module alias than the rest. Then
it's just a matter of using the right aliases according to what
algorithms we're trying to find.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
