L2CAP uses retransmission and monitor timers to inquiry the other side
about unacked I-frames. After sending each I-frame we (re)start the
retransmission timer. If it expires, we start a monitor timer that send a
S-frame with P bit set and wait for S-frame with F bit set. If monitor
timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving an I-frame with unexpected txSeq, receiver side start the
recovery procedure by sending a REJ S-frame to the transmitter side. So
the transmitter can re-send the lost I-frame.
This patch just adds a basic support for retransmission, it doesn't
mean that ERTM now has full support for packet retransmission.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERTM should use Segmentation and Reassembly to break down a SDU in many
PDUs on sending data to the other side.
On sending packets we queue all 'segments' until end of segmentation and
just the add them to the queue for sending. On receiving we create a new
SKB with the SDU reassembled.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for ERTM transfers, without retransmission, with
txWindow up to 63 and with acknowledgement of packets received. Now the
packets are queued before call l2cap_do_send(), so packets couldn't be
sent at the time we call l2cap_sock_sendmsg(). They will be sent in
an asynchronous way on later calls of l2cap_ertm_send(). Besides if an
error occurs on calling l2cap_do_send() we disconnect the channel.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to config_req and config_rsp to configure ERTM and Streaming
mode. If the remote device specifies ERTM or Streaming mode, then the
same mode is proposed. Otherwise ERTM or Basic mode is used. And in case
of a state 2 device, the remote device should propose the same mode. If
not, then the channel gets disconnected.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To enable Enhanced Retransmission mode it needs to be set via a socket
option. A different mode can be set on a socket, but on listen() and
connect() the mode is checked and ERTM is only allowed if it is enabled
via the module parameter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev->req_lock is used as mutex so make it a mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device model itself has no real usable reference counting at the
moment and this causes problems if parents are deleted before their
children. The device model itself handles the memory details of this
correctly, but the uevent order is not consistent. This causes various
problems for systems like HAL or even X.
So until device_put() does a proper cleanup, the device for Bluetooth
connection will be protected with an extra reference counting to ensure
the correct order of uevents when connections are terminated.
This is not an automatic feature. Higher Bluetooth layers like HIDP or
BNEP should grab this new reference to ensure that their uevents are
send before the ones from the parent device.
Based on a report by Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A couple of references to CONFIG_CLASSIC_RCU have survived.
Although these are harmless, it is past time for them to go.
The one in hardirq.h is strictly a readability problem.
The two in pagemap.h appear to disable a !SMP performance
optimization (which this patch re-enables).
This does raise the issue as to whether pagemap.h should really
be referring to the CPU implementation. Long term, I intend to
make the RCU implementation driven by CONFIG_PREEMPT, at which
point these should change from defined(CONFIG_TREE_RCU) to
!defined(CONFIG_PREEMPT). In the meantime, is there something
else that could be done in pagemap.h?
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josht@linux.vnet.ibm.com
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
LKML-Reference: <20090822050851.GA8414@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some of the NOPs tables aren't used on 64-bits, quite some code and
data is needed post-init for module loading only, and a couple of
functions aren't used outside that file (i.e. can be static, and don't
need to be exported).
The change to __INITDATA/__INITRODATA is needed to avoid an assembler
warning.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8BC8A00200007800010823@vpn.id2.novell.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
After talking with some application writers who want very fast, but not
fine-grained timestamps, I decided to try to implement new clock_ids
to clock_gettime(): CLOCK_REALTIME_COARSE and CLOCK_MONOTONIC_COARSE
which returns the time at the last tick. This is very fast as we don't
have to access any hardware (which can be very painful if you're using
something like the acpi_pm clocksource), and we can even use the vdso
clock_gettime() method to avoid the syscall. The only trade off is you
only get low-res tick grained time resolution.
This isn't a new idea, I know Ingo has a patch in the -rt tree that made
the vsyscall gettimeofday() return coarse grained time when the
vsyscall64 sysctrl was set to 2. However this affects all applications
on a system.
With this method, applications can choose the proper speed/granularity
trade-off for themselves.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: nikolag@ca.ibm.com
Cc: Darren Hart <dvhltc@us.ibm.com>
Cc: arjan@infradead.org
Cc: jonathan@jonmasters.org
LKML-Reference: <1250734414.6897.5.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: add GET_PARAM/INFO support for Z pipes
drm/radeon/kms: add r100/r200 OQ support.
drm: Fix sysfs device confusion.
drm/radeon/kms: implement the bo busy ioctl properly.
When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not. In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.
So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.
Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently when built with DEBUG DAPM will dump information about
the power state decisions it is taking for each widget to dmesg.
This isn't an ideal way of getting the information - it requires
a kernel build to turn it on and off and for large hub CODECs the
volume of information is so large as to be illegible. When the
output goes to the console it can also cause a noticable impact
on performance simply to print it out.
Improve the situation by adding a dapm directory to our debugfs
tree containing a file per widget with the same information in
it. This still requires a decision to build with debugfs support
but is easier to navigate and much less intrusive.
In addition to the previously displayed information active streams
are also shown in these files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a SETCLIENTID call comes in, one of the args given is the svc_rqst.
This struct contains an rq_addr field which holds the address that sent
the call. If this is an IPv6 address, then we can use the sin6_scope_id
field in this address to populate the sin6_scope_id field in the
callback address.
AFAICT, the rq_addr.sin6_scope_id is non-zero if and only if the client
mounted the server's link-local address.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
...rather than as a separate address and port fields. This will be
necessary for implementing callbacks over IPv6. Also, convert
gen_callback to use the standard rpcuaddr2sockaddr routine rather than
its own private one.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
It's currently a __be32, which isn't big enough to hold an IPv6 address.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
lockd needs these sort of routines, as does the NFSv4 callback code.
Move lockd's routines into common code and rename them so that they can
be used by others.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This include is needed for the definition of delayed_work.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This driver is very simple.
It support playback only now.
This patch is tested by ms7724se board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My patch "cfg80211: fix deadlock" broke the code it
was supposed to fix, the scan request checking. But
it's not trivial to put it back the way it was, since
the original patch had a deadlock.
Now do it in a completely new way: queue the check
off to a work struct, where we can freely lock. But
that has some more complications, like needing to
wait for it to be done before the wiphy/rdev can be
destroyed, so some code is required to handle that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are not maste devices in mac802154 anymore, so drop
ARPHRD_IEEE802154_PHY definition.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
IEEE 802.15.4-2006 adds new concept: channel pages, which can contain several
channels. Add support for channel pages in the API and in the fakehard driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: teardown crtc correctly when fb is destroyed.
drm/kms/radeon: cleanup combios TV table like DDX.
drm/radeon/kms: memset the allocated framebuffer before using it.
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
drm/radeon/kms: implement bo busy check + current domain
drm/radeon/kms: cut down indirects in register accesses.
drm/radeon/kms: Fix up vertical blank interrupt support.
drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
drm/edid: fixup detailed timings like the X server.
drm/radeon/kms: Add specific rs690 authorized register table
Extract duplicate code. Also prepare for the later patch.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A8BAFB8.1010304@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This parameter is needed by syscall events to add define_fields()
handler.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A8BAF90.6060801@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Common resources, like memory accounting and swap lists should be
global and not per device. Introduce a struct ttm_bo_global to
accomodate this, and register it with sysfs. Add a small sysfs interface
to return the number of active buffer objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Use inclusive zones to simplify accounting and its sysfs representation.
Use DMA32 accounting where applicable.
Add a sysfs interface to make the heuristically determined limits
readable and configurable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Export utility functions for drivers to add specialized devices in the
sysfs drm class subdirectory.
Initially this will be needed form TTM to add a virtual device that
handles power management.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A micro-optimization on the function ttm_kmap_obj_virtual().
By defining the values of enum ttm_bo_kmap_obj::bo_kmap_type to have a
bit indicating iomem, size of the function ttm_kmap_obj_virtual() will be
reduced by 16 bytes on x86_64 (gcc 4.1.2).
ttm_kmap_obj_virtual() may be heavily used, when buffer objects are
accessed via wrappers, that work for both kinds of memory addresses:
iomem cookies and kernel virtual.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we're using the scaling property in the Intel driver I noticed
that the names were a bit confusing. I've corrected them according to
our discussion on IRC and the mailing list, though I've left out
potential new additions for a new scaling property with an integer (or
two) for the scaling factor. None of the drivers implement that today,
but if someone wants to do it, I think it could be done with the
addition of a single new type and a new property to describe the
scaling factor in the X and Y directions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I misunderstood the meaning of __bitwise. In practice it makes sparse
warn about every use of mmds which is certainly not what we want.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
