From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->set_capacity block device method and use it in rescan_partitions()
to attempt enabling native capacity of the device upon detecting the
partition which exceeds device capacity.
* Add GENHD_FL_NATIVE_CAPACITY flag to try limit attempts of enabling
native capacity during partition scan.
Together with the consecutive patch implementing ->set_capacity method in
ide-gd device driver this allows automatic disabling of Host Protected Area
(HPA) if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the forcedeth device ids from pci_ids.h
The forcedeth driver uses the device id constants directly in its source
file.
[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
drivers/pci/quirks.c building -DaveM ]
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge reason: This branch was on an -rc5 base so pull almost-2.6.30
to resync with the latest upstream fixes and make sure
the combination works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Retrieval of an fw_unit's parent is a common pattern in high-level code.
Wrap it up as device = fw_parent_device(unit).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Extend generic event enumeration with the PERF_TYPE_HW_CACHE
method.
This is a 3-dimensional space:
{ L1-D, L1-I, L2, ITLB, DTLB, BPU } x
{ load, store, prefetch } x
{ accesses, misses }
User-space passes in the 3 coordinates and the kernel provides
a counter. (if the hardware supports that type and if the
combination makes sense.)
Combinations that make no sense produce a -EINVAL.
Combinations that are not supported by the hardware produce -ENOTSUP.
Extend the tools to deal with this, and rewrite the event symbol
parsing code with various popular aliases for the units and
access methods above. So 'l1-cache-miss' and 'l1d-read-ops' are
both valid aliases.
( x86 is supported for now, with the Nehalem event table filled in,
and with Core2 and Atom having placeholder tables. )
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Counter type is a frequently used value and we do a lot of
bit juggling by encoding and decoding it from attr->config.
Clean this up by creating a separate attr->type field.
Also clean up the various similarly complex user-space bits
all around counter attribute management.
The net improvement is significant, and it will be easier
to add a new major type (which is what triggered this cleanup).
(This changes the ABI, all tools are adapted.)
(PowerPC build-tested.)
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add bbt_wait & unlock_all as replaceable for some platform such as
s3c64xx s3c64xx has its own OneNAND controller and another interface
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for Samsung Flex-OneNAND devices.
Flex-OneNAND combines SLC and MLC technologies into a single device.
SLC area provides increased reliability and speed, suitable for storing
code such as bootloader, kernel and root file system. MLC area
provides high density and is suitable for storing user data.
SLC and MLC regions can be configured through kernel parameter.
[akpm@linux-foundation.org: export flexoand_region and onenand_addr]
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Vishak G <vishak.g@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add optional callback to allow platform to initialize partitions.
Static partitions on a nand device could vary depending on the size of the
device. This patch allows an optional platform callback to be used to
setup this partition information at runtime.
Scan order is:
1) chip.part_probe_types
2) chip.set_parts
3) chip.partitions
4) full mtd device (fallback for no partitions)
Some of the existing nand drivers could possibly be replaced by the
plat_nand driver by using this patch. These include autcpu12.c and
ts7250.c drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add optional probe and remove callbacks to the plat_nand driver.
Some platforms may require additional setup, such as configuring the
memory controller, before the nand device can be accessed. This patch
provides an optional callback to handle this setup as well as a callback
to teardown the setup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds (write|read)_buf callbacks to plat_nand.
The NAND on the TS-7800 provisioned by the FPGA allows readw() and
readl() to be used which gives a 2.5x speed up. To be able to use this
from the plat_nand driver a hook for read_buf (and also write_buf whilst
we are in there) need to be made available. This patch adds the hook.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In addition to adding the Numonyx manufacturer code, this patch
also ensures 'sync. write' is disabled when reading identification
data - something that the Numonyx chip objects to, but the
Samsung chip seems to ignore.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In order to allow easy tracking of the period, also provide means of
adding it to the sample data.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The purpose of PERF_SAMPLE_CONFIG was to identify the counters,
since then we've added counter ids, use those instead.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a PNP resource range check function, indicating whether a resource
has been assigned to any device.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
[apw@canonical.com: fixed up exports et al]
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The three header files of firewire-core, i.e.
"drivers/firewire/fw-device.h",
"drivers/firewire/fw-topology.h",
"drivers/firewire/fw-transaction.h",
are replaced by
"drivers/firewire/core.h",
"include/linux/firewire.h".
The latter includes everything which a firewire high-level driver (like
firewire-sbp2) needs besides linux/firewire-constants.h, while core.h
contains the rest which is needed by firewire-core itself and by low-
level drivers (card drivers) like firewire-ohci.
High-level drivers can now also reside outside of drivers/firewire
without having to add drivers/firewire to the header file search path in
makefiles. At least the firedtv driver will be such a driver.
I also considered to spread the contents of core.h over several files,
one for each .c file where the respective implementation resides. But
it turned out that most core .c files will end up including most of the
core .h files. Also, the combined core.h isn't unreasonably big, and it
will lose more of its contents to linux/firewire.h anyway soon when more
firewire drivers are added. (IP-over-1394, firedtv, and there are plans
for one or two more.)
Furthermore, fw-ohci.h is renamed to ohci.h. The name of core.h and
ohci.h is chosen with regard to name changes of the .c files in a
follow-up change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In order to track the vdso also generate mmap events for
install_special_mapping().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adds support for specifying a range of queues instead of a single queue
id. Flows will be distributed across the given range.
This is useful for multicore systems: Instead of having a single
application read packets from a queue, start multiple
instances on queues x, x+1, .. x+n. Each instance can process
flows independently.
Packets for the same connection are put into the same queue.
Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The "trace || CLONE_PTRACE" check in tracehook_report_clone() is not right,
- If the untraced task does clone(CLONE_PTRACE) the new child is not traced,
we must not queue SIGSTOP.
- If we forked the traced task, but the tracer exits and untraces both the
forking task and the new child (after copy_process() drops tasklist_lock),
we should not queue SIGSTOP too.
Change the code to check task_ptrace() != 0 instead. This is still racy, but
the race is harmless.
We can race with another tracer attaching to this child, or the tracer can
exit and detach in parallel. But giwen that we didn't do wake_up_new_task()
yet, the child must have the pending SIGSTOP anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can be used for other arm platforms too as discussed
on the linux-arm-kernel list.
Also check the return value with IS_ERR and return PTR_ERR
as suggested by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nomadik 8815 SoC has a slightly modified version of the PL011 block.
The patch uses the different ID value as a key to select a vendor
structure that is used to keep track of the differences, as suggested
by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In name of keeping it simple, only track mmap events. Userspace
will have to remove old overlapping maps when it encounters them.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create a fork event so that we can easily clone the comm and
dso maps without having to generate all those events.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As it stands skb fraglists can get past the check in dev_queue_xmit
if the skb is marked as GSO. In particular, if the packet doesn't
have the proper checksums for GSO, but can otherwise be handled by
the underlying device, we will not perform the fraglist check on it
at all.
If the underlying device cannot handle fraglists, then this will
break.
The fix is as simple as moving the fraglist check from the device
check into skb_gso_ok.
This has caused crashes with Xen when used together with GRO which
can generate GSO packets with fraglists.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the dependency of mmap_min_addr on CONFIG_SECURITY.
It also sets a default mmap_min_addr of 4096.
mmapping of addresses below 4096 will only be possible for processes
with CAP_SYS_RAWIO.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Eric Paris <eparis@redhat.com>
Looks-ok-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Sometimes it is necessary to know how the state is,
and it is easier to query rfkill than keep track of
it somewhere else, so add a function for that. This
could later be expanded to return hard/soft block,
but so far that isn't necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new code added by this patch will make rfkill create
a misc character device /dev/rfkill that userspace can use
to control rfkill soft blocks and get status of devices as
well as events when the status changes.
Using it is very simple -- when you open it you can read
a number of times to get the initial state, and every
further read blocks (you can poll) on getting the next
event from the kernel. The same structure you read is
also used when writing to it to change the soft block of
a given device, all devices of a given type, or all
devices.
This also makes CONFIG_RFKILL_INPUT selectable again in
order to be able to test without it present since its
functionality can now be replaced by userspace entirely
and distros and users may not want the input part of
rfkill interfering with their userspace code. We will
also write a userspace daemon to handle all that and
consequently add the input code to the feature removal
schedule.
In order to have rfkilld support both kernels with and
without CONFIG_RFKILL_INPUT (or new kernels after its
eventual removal) we also add an ioctl (that only exists
if rfkill-input is present) to disable rfkill-input.
It is not very efficient, but at least gives the correct
behaviour in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NETDEV_UP is called after the device is set UP, but sometimes
it is useful to be able to veto the device UP. Introduce a
new NETDEV_PRE_UP notifier that can be used for exactly this.
The first use case will be cfg80211 denying interfaces to be
set UP if the device is known to be rfkill'ed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the key length for validation, use the
constants Zhu Yi recently added and add one for AES_CMAC too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFC5061 had changed the error cause codes for Dynamic Address
Reconfiguration As the following:
Cause Code
Value Cause Code
--------- ----------------
0x00A0 Request to Delete Last Remaining IP Address
0x00A1 Operation Refused Due to Resource Shortage
0x00A2 Request to Delete Source IP Address
0x00A3 Association Aborted Due to Illegal ASCONF-ACK
0x00A4 Request Refused - No Authorization
This patch fix the error cause codes.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Can remove anonymous union now it has one field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sk_buff uses one union to define dst and rtable fields.
We want to replace direct access to these pointers by accessors.
First patch adds a new "unsigned long _skb_dst;" opaque field
in this union.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the notify chain infrastructure and replace it
by a simple function pointer. This issue has been mentioned in the
mailing list several times: the use of the notify chain adds
too much overhead for something that is only used by ctnetlink.
This patch also changes nfnetlink_send(). It seems that gfp_any()
returns GFP_KERNEL for user-context request, like those via
ctnetlink, inside the RCU read-side section which is not valid.
Using GFP_KERNEL is also evil since netlink may schedule(),
this leads to "scheduling while atomic" bug reports.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
blk_queue_bounce_limit() is more than a wrapper about the request queue
limits.bounce_pfn variable. Introduce blk_queue_bounce_pfn() which can
be called by stacking drivers that wish to set the bounce limit
explicitly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The structure isn't hw only and when I read event, I think about those
things that fall out the other end. Rename the thing.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since some people worried that 4G might not be a large enough
as an mmap data window, extend it to 64 bit for capable
platforms.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ (non-NMI) sampling is not used anymore - remove the last few bits.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
