If the VF sends a bad message, be more informative about what it
actually is.
Change-Id: I89e06d2db416a1d05aeea016dd6e8b7870cae99a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF asks to add an invalid MAC address, tell it that instead of
just using a generic return code.
Change-Id: I366aff5449fa5874ad51e2734cac2a71783ab14b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.
Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't keep separate functions to enable and disable queues for the VFs.
Just call the existing function that everybody else uses. Remove the
unused functions.
Change-Id: I15db9aad64a59e502bfe1e0fdab9b347ab85c12c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the VF reset flow so that it works on real hardware. After
discussions with the HW team, the reset flow has been changed
somewhat.
- Change the i40e_reset_vf function to a void type, and fix
up the callers to reflect this.
- Move the MSI-X disable code to i40e_free_vf_res since it must
be done every time the VF is freed, regardless of whether or
not it is reset.
- Ensure that the PCIe bus is quiet before polling the reset bit.
- Don't clear the VFGEN_RSTAT1 register at the beginning as it is
cleared by the reset.
- Poll longer for the reset to be done.
- Disable the queues using an existing function rather than
rolling our own.
- Free and reallocate the VSI after reset to avoid rx hang.
Change-Id: I11e2590431cb73e8663714d1cc5b23d59b809033
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF reset code will be refactored in future patches. Part of that
refactor required it to call i40e_alloc_vf_res and i40e_free_vf_res, so
the function must be moved. In order to make the future patches more
readable, we perform the function move here, with no other changes.
Change-Id: If6567c9c0bada6caafb2ee0227e0d9d50d05f27f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements receive offload for VXLAN for i40e. The hardware
supports checksum offload/verification of the inner/outer header.
Change-Id: I450db300af6713f2044fef1191a0d1d294c13369
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the implementation for the VXLAN ndo's. This allows the
hardware to do RX checksum offload for inner packets on the UDP ports
that VXLAN notifies us about.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add curly-braces on a multi-line function. While we're here we
also change to return void in i40e_vsi_clear_rings() since no
caller cares.
Change-Id: I261fcef20e2a39e18d83ec08fdd14456131dee91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wake on LAN is disabled by default and will remain that way for most
platforms, but there is an NVM setting that allows vendors to enable it
for a port if they think they've provided the right power environment
for the device. This patch adds code to check the NVM setting and enable
Magic Packet use if WoL is enabled for the port.
Since only Magic Packet is supported, there's not a lot of HW configuration
needed.
Change-Id: I44e904a7b15695e34683009f487064cd86ea59b0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call i40e_set_pci_config_data from probe, then check that
we are in a 8GT/s x8 PCIe slot and send a warning if we are not.
Change-Id: I62815c574cee50d2787c50bbe956dde7a7a75a11
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HMC error interrupt would generate an un-necessary message
"unhandled interrupt", causing extra log spam, in addition to causing
a reset that was not necessary. Prevent this issue by handling the
HMC error case explicitly, and only reset if the interrupt was from
some of the other causes.
Change-Id: Iabd203ba1dfc26a136b638597f3e9991acfa29f3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ASF enabled devices where the mgmt firmware runs on the application
processing engine, there is a race between the tg3 driver processing a
link change event and the ASF firmware clearing the link changed bit in
the EMAC status register. This leads to link notifications to the driver
sometimes getting lost.
Poll the CPMU link state as a backup for the normal interrupt path
update if ASF is enabled.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the 5717, 5718 and 5719 devices, the bootcode runs slower when any
port doesn't have a link due to clock speed slowing down as part of the
link-aware feature. This leads to the driver timing out waiting for the
bootcode signature.
This patch overrides the clock policy to the highest frequency just before
reset and restores it after the bootcode is up.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to 3 additional unicast addresses can be added to the perfect match
filter table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that individual MAC address filter entries can be set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running 'scripts/checkpatch.pl' on the driver files gives numerous warnings:
- block comments using empty /* line;
- unneeded \ at end of lines;
- message string split across lines;
- use of __attribute__((aligned(n))) instead of __aligned(n) macro;
- use of __attribute__((packed)) instead of __packed macro.
Additionally, running 'scripts/checkpatch.pl --strict' gives more complaints:
- including the paragraph about writing to FSF into the heading comment;
- alignment not matching open paren;
- multiple assignments on one line;
- use of CamelCase names;
- missing {} on one of the *if* arms where another has them;
- spinlock definition without a comment.
While fixing these, also do some more style cleanups:
- remove useless () around expressions;
- add {} around multi-line *if* operator's arm;
- remove space before comma;
- add spaces after /* and before */;
- properly align continuation lines of broken up expressions;
- realign comments to the structure fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is using common tx_clean_lock for all Tx queues. This patch
adds per queue tx_clean_lock.
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Fixed in this patch.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
@@
pci_enable_wake(e1,
- 0
+ PCI_D0
,e2)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev_priv performs an addition, not a pointer dereference, so it seems
quite unlikely that its result would ever be NULL.
A semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
statement S;
@@
- if (!netdev_priv(...)) S
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 52367a763d
("cxgb4/cxgb4vf: Code cleanup to enable T4 Configuration File support"),
we have failures like this during cxgb4 probe:
cxgb4 0000:01:00.4: bad SGE FL page buffer sizes [65536, 65536]
cxgb4: probe of 0000:01:00.4 failed with error -22
This happens whenever software parameters are used, without a
configuration file. That happens when the hardware was already
initialized (after kexec, or after csiostor is loaded).
It happens that these values are acceptable, rendering fl_pg_order equal
to 0, which is the case of a hard init when the page size is equal or
larger than 65536.
Accepting fl_large_pg equal to fl_small_pg solves the issue, and
shouldn't cause any trouble besides a possible performance reduction
when smaller pages are used. And that can be fixed by a configuration
file.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TX queues allocation was getting distributed equally among all the
functions of the port including VFs and PF. Which was leading to failure
in PF's multiple TX queues creation.
o Instead of dividing queues equally allocate one TX queue for each VF as VF
doesn't support multiple TX queues.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter requires that if the port is in loopback mode no traffic should
be flowing through that port, so on arrival of Link up AEN, do not advertise
Link up to the stack until port is out of loopback mode
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hwtstamp_config matches what is currently set for the device then
simply return. Without this change any program that tries to enable
hardware timestamps will cause the link to cycle even if hardware
timstamps were already enabled.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a PHC to the mlx4_en driver. We use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
This driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-3 card.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the return variable to propagate any error code as done elsewhere in
the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make variables only used in one file static. Also avoids possible
namespace collisions.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series implements the Linux Virtual Function (VF) driver for
the Intel Ethernet Controller XL710 family.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
KR2 work-around is based on detecting non-KR2 devices which may not link up
in this mode. One such link-partner is the BCM8073 which has specific
advertisement characteristics in specific mode, and this condition was not set
correctly.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where link is reported to be up when SFP+ module is plugged in
without cable. This occurs with specific module types which may generate
temporary TX_FAULT indication. Solution is to avoid changing any link parameters
when checking TX_FAULT indication while physical link is down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54618SE is used to advertise half-duplex even if HD was not requested by the
user. This change makes the legacy speed/duplex advertisement for this PHY
exactly according to the requested speed and duplex.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Passive DAC detection for specific cables, such that even in case
SFP_CABLE_TECHNOLOGY option is not set in the EEPROM (offset 8), treat it as a
passive DAC cable, since some cables don't have this indication.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where 578xx-KR is unable to get link when connected to 1G link
partner. Two fixes were required:
One was to force CL37 sync_status low to prevent Warpcore from getting stuck in
CL73 parallel detect loop while link partner is sending.
Second fix was to enable auto-detect mode, thus allowing the Warpcore to select
the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73
when there's indication for it.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer that is used to pass doorbell offset to the userspace UIO
driver may contain nonzero value in older versions of bnx2x driver.
Userspace cannot easily tell whether it contains a valid doorbell
offset or not. With the added signature, userspace will only use
the doorbell offset if the signature is present.
Update version to 2.5.19.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-mdix currently only works if autoneg is enabled. This patch enables
auto-mdix all the time by setting a bit in a PHY register. Define
meaningful constants for this PHY registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not reset the advertisement register when the speed
is forced, leaving the default advertisement value of 10 Mbps. This does
not work with some link partners when the next patch enables auto-mdix.
Set advertisement register to 0 if the speed is forced.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 stepping silicon specific code
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the hardware specific init and management.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing structures
and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code
to Linux.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This PCI-E SR-IOV virtual function (VF) driver is dependant upon the
physical function (PF) driver (i40e) for nearly all of its hardware
configuration. Requests from the VF driver are passed to the PF using
the hardware's Admin Queue.
This patch contains the functionality for communicating with the PF
driver. Because of the delay inherent in this communications channel,
most of the replies from the PF driver are handled asynchronously. The
exceptions are the "send API version" and "get VF config" messages,
which busy-wait because they are done so early during init that
interrupts are not yet configured.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the ethtool interface and related functionality.
Since the VF driver is mostly unaware of link, much of that
functionality is unused. The driver implements ethtool hooks for
statistics, driver info, and some basic non-link-related driver
settings.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This file contains the transmit, receive, and NAPI functionality.
Some of the functions in this module are extracted from the i40e driver
but functions that are not appropriate for virtual function devices have
been removed.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the driver for the Intel(R) XL710 X710 Virtual Function.
This patch contains the main driver entry points, but does not include
transmit and receive or ethtool functionality, which are presented as
separate patches in this series.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
