Touching the VGA registers risks a hard machine hang, at least on this
ivb machine after removing a conflicting efifb. This is more than likely
related to the discovery that VGA IO decode on the more recent PCH
platforms is terminally broken.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has very little effect other than log the errors in case of failure,
and we then hope for the best.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allocate this struct instead, so we can re-use another allocated
elsewhere if needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: WARN_ON if there's no backing storage attached to an fb,
that's a bug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we detect that the user passed along an invalid handle or object,
we emit a warning as an aide for debugging. Since these are indeed only
for debugging user triggerable errors (and the errors are reported back
to userspace by the errno), the messages should only be at the debug
level and not claiming that there is a catastrophic error in the
driver/hardware.
References: https://bugs.freedesktop.org/show_bug.cgi?id=74704
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had 2 set of defines for the same register, so make it one.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And rename it to num_sprites as this value doesn't count the primary
plane.
This limit lives with num_pipes really, and now that dev_priv->info is
writable we can put it there instead.
While at it, introduce a intel_device_info_runtime_init() where we'll be
able to gather the device info fields at run-time.
v2: rename num_plane to num_sprites (Ville Syrjälä)
v3: rebase on top of latest drm-nightly
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out it'd be nice to change some device information at run-time or simply
have some code to fill in the info struct instead of having to declare the
values in 30+ structures.
What prompted this change is handling fused out display/pipe and tweaking
num_pipes at run-time, but I'm quite sure we'll find other flags/limits to
stick into dev_priv->info.
Most of the changes were done with a sed:
sed -i -e 's/dev_priv->info->/dev_priv->info./g' drivers/gpu/drm/i915/*[ch]
with a few tweaks to make it all work:
- Change the field definition in struct drm_i915_private
- adjust i915_dump_device_info()
- adjust i915_driver_load()
- adjust the INTEL_INFO() macro
v2: cast the info pointer returned by INTEL_INFO() to be const to catch
uses that would modify the structure post-initialization.
(Ville Syrjälä)
v3: Redo the patch onto latest drm-nightly,
Keep the info field const to catch post initialization writes
instead of the v2 solution,
Use a direct structure copy for the initial info initialization to
use the compiler type safety (Ville Syrjälä)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we make sure that all the dev_priv->info usages are wrapped by
INTEL_INFO(), we can easily modify the ->info field to be structure and
not a pointer while keeping the const protection in the INTEL_INFO()
macro.
v2: Rebased onto latest drm-nightly
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Bspec we need to disable SF pipelined attribute fetch
whenever SF outputs exceed 16 and normal clip mode is used. A quick
glance at Mesa suggests that these conditions could happen. So let's
just always set the magic bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
3 regression fixes in i915
* tag 'drm-intel-fixes-2014-02-11' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915: Pair va_copy with va_end in i915_error_vprintf
drm/i915: Fix intel_pipe_to_cpu_transcoder for UMS
drm/i915: Disable dp aux irq on g4x
According to BSpec the entire MI_DISPLAY_FLIP packet must be contained
in a single cacheline. Make sure that happens.
v2: Use intel_ring_begin_cacheline_safe()
v3: Use intel_ring_cacheline_align() (Chris)
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74053
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_ring_cachline_align() emits MI_NOOPs until the ring tail is
aligned to a cacheline boundary.
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org (prereq for the next patch)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Each invocation of va_copy() must be matched by a corresponding
invocation of va_end() in the same function.
This regression has been introduced in
commit e29bb4ebbf
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Sep 20 10:20:59 2013 +0100
drm/i915: Use a temporary va_list for two-pass string handling
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have all the drm_crtc&co hanging around in that case.
This regression has been introduced in
commit 391f75e2bf
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Sep 25 19:55:26 2013 +0300
drm/i915: Fix pre-CTG vblank counter
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=69521
Cc: stable@vger.kernel.org (for 3.13 only)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just minor stuff really, on vlv dp fix and two patches to tune down some
opregion sanity check. Plus MAINTAINERS update for the new git repo, which
is the only reason I've really bothered with this pull request.
* tag 'drm-intel-fixes-2014-02-06' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915: demote opregion excessive timeout WARN_ONCE to DRM_INFO_ONCE
drm: add DRM_INFO_ONCE() to print a one-time DRM_INFO() message
MAINTAINERS: Update drm/i915 git repo
drm/i915: vlv: fix DP PHY lockup due to invalid PP sequencer setup
Apparently it's broken in the exact same way as the gmbus irq. For
reference of the full story see
commit c12aba5aa0
Author: Jiri Kosina <jkosina@suse.cz>
Date: Tue Mar 19 09:56:57 2013 +0100
drm/i915: stop using GMBUS IRQs on Gen4 chips
The effect is that we have a storm of unclaimed interrupts on the
legacy irq line. If that one is used by a different device then the
kernel will complain and rather quickly kill the irq source. Which
breaks any device trying to actually use the legacy irq line.
This regression has been introduced
commit 4aeebd7443
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 31 09:53:36 2013 +0100
drm/i915: dp aux irq support for g4x/vlv
Note that disabling MSI works around the issue, but we can't do that
since apparently then the hw will miss interrupts. At least if
relevant comments in i915_irq.c are accurate.
v2: Cross-reference dp aux and gmbus gen4 comments.
v3: Consolidate harder into i915_drv.h as suggested by Chris.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
sysfs changes to rps min and max delay were only triggering an update
of the rps interrupt limits if the active delay required an update.
This change ensures that interrupt limits are always updated.
v2: correct compile issue missed on rebase
v3: add igt testcases to signed-off-by section
Testcase: igt/pm_rps/min-max-config-idle
Testcase: igt/pm_rps/min-max-config-loaded
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A check of rps/rc6 state after i915_reset determined that the ring
MAX_IDLE registers were returned to their hardware defaults and that
the GEN6_PMIMR register was set to mask all interrupts. This change
restores those values to their pre-reset states by re-initializing
rps/rc6 in i915_reset. A full re-initialization was opted for versus
a targeted set of restore operations for simplicity and maintain-
ability. Note that the re-initialization is not done for Ironlake,
due to a past comment that it causes problems.
Also updated the rps initialization sequence to preserve existing
min/max values in the case of a re-init. We assume the values were
validated upon being set and do not do further range checking. The
debugfs interface for changing min/max was updated with range
checking to ensure this condition (already present in sysfs
interface).
v2: fix rps logging to output hw_max and hw_min, not rps.max_delay
and rps.min_delay which don't strictly represent hardware limits.
Add igt testcase to signed-off-by section.
Testcase: igt/pm_rps/reset
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the VM do not track activity of objects and instead use a large
hammer to forcibly idle and evict all of their associated objects when
one is released, it is possible for that to cause a recursion when we
need to wait for free space on a ring and call retire requests.
(intel_ring_begin -> intel_ring_wait_request ->
i915_gem_retire_requests_ring -> i915_gem_context_free ->
i915_gem_evict_vm -> i915_gpu_idle -> intel_ring_begin etc)
In order to remove the requirement for calling retire-requests from
intel_ring_wait_request, we have to inline a couple of steps from
retiring requests, notably we have to record the position of the request
we wait for and use that to update the available ring space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We get a large number of bugs which have a, "hey I have that too"
because they see a GPU hang in dmesg. While two machines of the same
model having a GPU hang is indeed a coincidence, it is far from enough
evidence to suggest they are the same.
In order to reduce this effect, and hopefully get people to file new bug
reports, clearly the error message itself has been insufficient (see ref
at the bottom for a new bug report with this characteristic).
The algorithm is purposely pretty naive. I don't think we need much in
order to avoid the problem I am trying to solve, and keeping it naive
gives us some ability to make a decent test case.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=73276
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
s/FLIPDONE/FLIP_DONE/ to make all FLIP_DONE macro names consistent.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be used by other platforms too, so factor it out.
The only functional change is the reordeing of gmbus_irq_handler() wrt.
the hotplug handling, but since it only schedules a work, it isn't an
issue.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't keep on using the private_t typedef.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec and the code suggests that the interrupt signaled by IIR[7,5]
(DISPLAY_PIPE_A/B_VBLANK) is a first level IRQ flag for the second
level PIPEA/BSTAT[2] (Start of Vertical Blank) interrupt. Measuring
the relative timings of when IIR[7] and PIPEASTAT[1,2] get set and
checking the effect of unmasking different pipestat and IIR events
shows that this isn't so:
First, ISR/IIR[7] gets set independently of PIPEASTAT[18] (Start of
Vertical Blank Enable) or any other pipestat enable bit, so it isn't
a first level IRQ bit showing the state of PIPEASTAT[2], but is
connected directly to the timing generator.
Second, setting only PIPEASTAT[18] and leaving all other pipestat events
disabled, IIR[6] (DISPLAY_PIPE_A_EVENT) gets set close to the moment when
PIPEASTAT[2] gets set, so the former is a first level interrupt flag for
the latter. The bspec is rather unclear about this, but I also assume
that IIR[6] signals all pipestat A events, except PIPEASTAT[31] (FIFO
Under-run Status).
Third, IIR[7] is set close to the moment when PIPEASTAT[1] (Framestart
Interrupt) gets set, in the mode I used about 12usec after PIPEASTAT[2]
and IIR[6] gets set. This means the IIR[7] isn't marking the start of
vblank, but rather signals the framestart event.
Based on the above, we don't need to unmask IIR[7] when waiting for
start of vblank events, but we can rely on IIR[6] being always unmasked,
which will signal when PIPEASTAT[2] gets set. Doing this will also get
rid of the overhead of getting an interrupt and servicing IIR[7], which
is atm raised always some time after IIR[6]/PIPEASTAT[2] is raised.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The WARN_ONCE is a bit too verbose, make it a DRM_INFO_ONCE.
While at it, add a #define for MAX_DSLP and make the message a bit more
informative.
v2: use DRM_INFO_ONCE, add MAX_DSLP, pimp the message.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since a purged buffer is one without any associated pages, attempting to
use it should generate EFAULT rather than EINVAL, as it is not strictly
an invalid parameter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
EFAULT will be a possible return code where backing storage is
transient, such after it is purged by madvise. As such it is to be
expected and so should not trigger a WARN inside i915_gem_fault() but be
converted silently to SIGBUS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we seek the guilty batch using request and hangcheck
score, this code is not needed anymore.
v2: Rebase. Passing dev_priv instead of getting it from last_ring
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt using acthd is not enough to find guilty
batch buffer. We get multiple false positives as acthd is
per vm.
Instead of scanning which vm was running on a ring,
to find corressponding context, use a different, simpler,
strategy of finding batches that caused gpu hang:
If hangcheck has declared ring to be hung, find first non complete
request on that ring and claim it was guilty.
v2: Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both Bspec and the W/A database state that WaDisablePSDDualDispatchEnable
is only needed for IVB GT1.
The only real confusion here is that the the W/A database also says to
write to the GT2 only register as well, which is strange if the W/A is
only for GT1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB GT2 has two registers for these things, and both must be written.
To add a bit more confusion both Bspec and the W/A database state that
WaDisablePSDDualDispatchEnable is only needed for IVB GT1, but the W/A
database also says to write even the second GT2 only register. So I
don't really know what the right thing here is.
Note that Bspec disagrees with the w/a database here, but Ville
confirmed (by asking Chris) that on gt1 the 2nd reg doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add note as requested by Rodrigo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we setup the HW panel power sequencer logic both for eDP and DP
ports. On eDP we then go on and start the power on sequence and commence
with link training when it's ready. On DP we don't do the power on
sequencing but do the link training immediately. At this point the DP
PHY block gets stuck, since - supposedly - it is waiting for the power
on sequence to finish. The actual register write that seems to hold off
the PHY is PIPEX_PP_ON_DELAYS[Panel Control Port Select]. Writing here
a non-0 value eventually sets PIPEX_PP_STATUS[Require Asset Status] to
1 and blocks the PHY until the panel power on is ready.
Fix this by not doing any PP sequencing setup for DP ports.
Thanks to Ville Syrjälä, Jesse Barnes and Todd Previte for the help in
tracking this down.
Note that on older gmch platforms (where we have lvds instead of edp)
we've hacked around this by writing the magic ABCD unlock key to PP
registers, which disables the hw sanity checks.
For edp all platforms thus far had the pch split, with the edp port in
the north display complex and the PP registers on the pch the hw
sanity checks (expressed through the "Require Asset Status" bit) was
never functional, hence never a real issue.
This regression has been introduce in
commit bf13e81b90
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about the bigger story here.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the GTT for reading back objects upon an error so that we
have exactly the information that the GPU saw. However, it is verboten
to access snoopable pages through the GTT and causes my PineView GPU to
throw a page fault instead.
This has not been a problem in the past as we only dumped ringbuffers
and batchbuffers, both of which must be not snooped. However, the
introduction of HWS page dumping leads to a read of a snooped object
through the GTT. This was introduced by
commit f3ce382139
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jan 23 22:40:36 2014 +0000
drm/i915: Include HW status page in error capture
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet:s/uncached/not snooped/ for one case in the commit message as
requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Repeating the same information multiple times is just annoying.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have stopped rings then we know that test is running
so no need for spam. In addition, only spam when default
context gets banned.
v2: - make sure default context ban gets shown (Chris)
- use helper for checking for default context, everywhere (Chris)
v3: - dont be quiet when debug is set (Ben, Daniel)
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt support drm_i915_file_private gained knowledge
about the default context. Also reset stats are now inside
i915_hw_context so we can use proper abstraction.
v2: Move BUG_ON and WARN_ON to more proper locations (Ben)
v3: Pass dev directly to i915_context_is_banned to avoid the need to
dereference ctx->last_ring. Spotted by Mika when checking my
s/BUG/WARN/ change, I've missed this ->last_ring dereference.
Suggested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> (v2)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v2)
[danvet: s/BUG/WARN/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization helps IVB too. No piglit regression.
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization is available on Ivy Bridge and later, and is disabled by
default. Enabling it helps certain workloads such as GLBenchmark TRex test.
No piglit regression.
v2
- no need to save the register before suspend as init_clock_gating can
correctly program it after resume
- split IVB change to another commit
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased upon cleaned up error state
v3: Make sure hangcheck info remains last (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris:
Do we also want to capture?
GAC_ECO_BITS /* gen6,7 */
GAM_ECOCHK /* gen6,7 */
GAB_CTL /* gen6 */
GFX_MODE /* gen6 */
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Moved num_requests up (Chris)
Rebased on new hws page capture which required a rename since it made
two members named, 'hws' in the per ring error state. (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This helps make an upcoming patch a bit more reviewable
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create logical sections in an attempt to clean up, and continue to keep
future additions clean.
v2: Reworded the comments. Added section headers (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code has become quite hairy. By relocating all the generic registers
it will become more obvious where future ones should go. There is still
admittedly a bit of confusion left for things like per ring registers.
A subsequent patch will clean this function up.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
