Let's say clock A and B are two gate clocks that share the same register
bit in hardware. Therefore they are registered as shared gate clocks
with imx_clk_gate2_shared().
In a scenario that only clock A is enabled by clk_enable(A) while B is
not used, the shared gate will be unexpectedly disabled in hardware.
It happens because clk_enable(A) increments the share_count from 0 to 1,
while clock B is unused to clock core, and therefore the core function
will just disable B by calling clk->ops->disable() directly. The
consequence of that call is share_count is decremented to 0 and the gate
is disabled in hardware, even though clock A is still in use.
The patch fixes the issue by initializing the share_count per hardware
state and returns enable state per share_count from .is_enabled() hook,
in case it's a shared gate.
While at it, add a check in clk_gate2_disable() to ensure it's never
called with a zero share_count.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: f9f28cdf21 ("ARM: imx: add shared gate clock support")
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- fix the check for SMP configuration with using CONFIG_SMP
not just SMP
- fix the number of pwm-cells for exynos4 pwm
- fix ftrace for exynos_mct
- register exynos_mct for stable udely
- fix secondary boot addr for secure mode for exynos SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jlRt
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-2 for v3.16" from Kukjin Kim:
- fix the check for SMP configuration with using CONFIG_SMP
not just SMP
- fix the number of pwm-cells for exynos4 pwm
- fix ftrace for exynos_mct
- register exynos_mct for stable udely
- fix secondary boot addr for secure mode for exynos SoCs
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update secondary boot addr for secure mode
clocksource: exynos_mct: Register the timer for stable udelay
clocksource: exynos_mct: Fix ftrace
ARM: dts: fix pwm-cells in pwm node for exynos4
ARM: EXYNOS: Fix the check for non-smp configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently CLK_FOUT_EPLL was set as one of the parents of AUDSS mux.
As per the user manual, it should be CLK_MAU_EPLL.
The problem surfaced when the bootloader in Peach-pit board set
the EPLL clock as the parent of AUDSS mux. While booting the kernel,
we used to get a system hang during late boot if CLK_MAU_EPLL was
disabled.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Almost all Exynos-series of SoCs that run in secure mode don't need
additional offset for every CPU, with Exynos4412 being the only
exception.
Tested on Origen-Quad (Exynos4412) and Arndale-Octa (Exynos5420).
While at it, fix the coding style (space around *).
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The revision checking in l2c310_enable() was not correct; we were
masking the part number rather than the revision number. Fix this
to use the correct macro.
Fixes: 4374d64933 ("ARM: l2c: add automatic enable of early BRESP")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, child nodes of the gpmc node are iterated and probed
regardless of their 'status' property. This means adding 'status =
"disabled";' has no effect.
This patch changes the iteration to only probe nodes marked as
available.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP platform device for TI DSP/Bridge is currently
created unconditionally whenever CONFIG_TIDSPBRIDGE is
enabled. This device should only be created on OMAP34xx/
OMAP36xx SoCs, and not for other OMAP3 derived SoCs or when
booting multi-arch images on other SoCs. So, add a check for
the SoC family both before creating the device and allocating
the carveout memory for the device.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap44xx_restart is defined as a static void inline when DRA7/AM437X is
defined alone, which implies that the restart function is no longer
functional even though it is built in. So, fix the definition of the
same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The divider value provided to the _dpll_test_fint can reach value of
256 with J type DPLLs (USB etc.), which causes an overflow with the u8
datatype. Fix this by changing the parameter to be an int instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: changed type of 'n' to unsigned int]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the sysconfig class bits for the Super Speed USB
controllers
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Get rid of optional clock as that is now managed by the
AHCI platform driver.
Correct .mpu_rt_idx to 1 as the module register space (SYSCONFIG..)
is passed as the second memory resource in the device tree.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The commit 7be914f {ARM: OMAP3: PRM/CM: Cleanup unused header} removed
some of the macros used by the TI DSP/Bridge driver. This fixes the
following build errors when trying to build DSP/Bridge driver (disabled
at present), otherwise results in the following build errors:
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/staging/tidspbridge/core/tiomap_io.c: In function 'sm_interrupt_dsp':
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap_io.c:414:12: error: 'OMAP3430_IVA2_DPLL_FREQSEL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:415:12: error: 'OMAP3430_EN_IVA2_DPLL_SHIFT' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap_io.o] Error 1
drivers/staging/tidspbridge/core/tiomap3430_pwr.c: In function 'dsp_clk_wakeup_event_ctrl':
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: error: 'OMAP3430_GRPSEL_GPT5_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:455:19: error: 'OMAP3430_GRPSEL_GPT6_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:468:19: error: 'OMAP3430_GRPSEL_GPT7_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:481:19: error: 'OMAP3430_GRPSEL_GPT8_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:494:19: error: 'OMAP3430_GRPSEL_MCBSP1_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:546:19: error: 'OMAP3430_GRPSEL_MCBSP5_MASK' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430_pwr.o] Error 1
make[2]: *** [drivers/staging/tidspbridge] Error 2
Fixes: 7be914f (ARM: OMAP3: PRM/CM: Cleanup unused header)
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
- Reset fix for am43xx
- Proper OPP table for omap5
- Fix for SoC detection of one of the DRA7 SoCs
- hwmod updates to get SATA and OCP to work on omap5 (drivers merged in 3.16)
- ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was removed in
anticipation of a watchdog driver being merged for 3.16, and it didn't make
it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this point
but it slipped through cracks repeatedly while coming up the maintainer
chain and only affects the one SoC so risk is low.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=J9xD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eDSn
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
This partly reverts commits 553600502b (ARM: sunxi: Remove reset code from
the platform) and 5e669ec583 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2HDE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
pwm-cells should be 3. Third cell is optional PWM flags. And This flag
supported by this binding is PWM_POLARITY_INVERTED.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 1754c42e3db5("ARM: exynos: move sysram info to exynos.c") missed
out the CONFIG_ prefix causing exynos_sysram_init() to get called twice
for SMP configurations.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsug.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Without the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
532000000
With the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
266000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
133000000
The l3 clock derived from core DPLL is actually a divider clock,
with the default divider set to 2. l4 then derived from l3 is a fixed factor
clock, but the fixed divider is 2 and not 1. Which means the l3 clock is
half of core DPLLs h12x2 and l4 is half of l3 (as seen with this patch)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Conditionally compile kprobes test cases for ARMv5 instructions to avoid
compilation errors with ARMv4 targets like:
/tmp/cc7Tx8ST.s:16740: Error: selected processor does not support ARM mode `clz r0,r0'
Signed-off-by: Jon Medhurst <tixy@linaro.org>
ARM data processing instructions which have a register specified shift
are defined as UNPREDICTABLE if PC is used for any register, not just
the shift value as the code was previous assuming. This issue manifests
on A15 devices as either test case failures or undefined instructions
aborts.
Reported-by: David Long <dave.long@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Due to a long-standing issue with Thumb symbol lookup [1] the jprobes
tests fail when built into a kernel compiled as Thumb mode. (They work
fine for ARM mode kernels or for Thumb when built as a loadable module.)
Rather than have this problem terminate testing prematurely lets instead
emit an error message and carry on with the main kprobes tests, delaying
the final failure report until the end.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2011-August/063026.html
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Commit 143e1e28cb (sched: Rework sched_domain topology definition)
introduced a number of functions with a return value of 'const int'.
gcc doesn't know what to do with that and, if the kernel is compiled
with W=1, complains with the following warnings whenever sched.h
is included.
include/linux/sched.h:875:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:882:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:889:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:1002:21: warning: type qualifiers ignored on function return type
Commits fb2aa855 (sched, ARM: Create a dedicated scheduler topology table)
and 607b45e9a (sched, powerpc: Create a dedicated topology table) introduce
the same warning in the arm and powerpc code.
Drop 'const' from the function declarations to fix the problem.
The fix for all three patches has to be applied together to avoid
compilation failures for the affected architectures.
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403658329-13196-1-git-send-email-linux@roeck-us.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The SMP boot on Armada 38x and Armada 375 Z1 is currently broken in
big-endian configurations, and this commit fixes it for both
platforms.
For Armada 375 Z1, the problem was in the
armada_375_smp_cpu1_enable_code part of the code that gets copied to
the Crypto SRAM as a work-around for an issue of the Z1 stepping. This
piece of code was not switching the CPU core to big-endian, and not
endian-swapping the value read from the Resume Address register (the
value is stored little-endian). Due to the introduction of the
conditional 'rev r1, r1' instruction, the offset between the 'ldr r0,
[pc, #4]' instruction and the value it was looking is different
between LE and BE configurations. To solve this, we instead use one
'adr' instruction followed by one 'ldr'.
For Armada 38x, the problem was simply that the CPU core was not
switched to big endian in the secondary CPU startup function.
This change was tested in LE and BE configurations on Armada 385,
Armada 375 Z1 and Armada 375 A0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404228186-21203-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On Marvell Armada XP, when a CPU comes back from deep idle state of
cpuidle, it restarts its execution at armada_370_xp_cpu_resume(),
which puts back the CPU into the coherency, and then calls the generic
cpu_resume() function.
While this works on little-endian configurations, it doesn't work on
big-endian configurations because the CPU restarts in little-endian,
and therefore must be switched back to big-endian to operate
properly. To achieve this, a 'setend be' instruction must be executed
in big-endian configurations. However, the ARM_BE8() macro that is
used to implement nice compile-time conditional for ARM LE vs. ARM BE8
is not easily usable in inline assembly.
Therefore, this patch moves the armada_370_xp_cpu_resume() C function,
which was anyway just a block of inline assembly, into a proper
pmsu_ll.S file, and adds the appropriate ARM_BE8(setend be)
instruction.
Without this patch, an Armada XP big endian configuration with cpuidle
enabled fails to boot, as it hangs as soon as one of the CPU hits the
deep idle state.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404130165-3593-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 497a92308a ("ARM: mvebu:
implement L2/PCIe deadlock workaround") introduced some logic in
coherency.c to adjust the PL310 cache controller Device Tree node of
Armada 375 and Armada 38x platform to include the 'arm,io-coherent'
property if the system is running with hardware I/O coherency enabled.
However, with the L2CC driver cleanup done by Russell King, the
initialization of the L2CC driver has been moved earlier, and is now
part of the init_IRQ() ARM function in
arch/arm/kernel/irq.c. Therefore, calling coherency_init() in
->init_time() is now too late, as the Device Tree property gets added
too late (after the L2CC driver has been initialized).
In order to fix this, this commit removes the ->init_time() callback
use in board-v7.c and replaces it with an ->init_irq() callback. We
therefore no longer use the default ->init_irq() callback, but we now
use the default ->init_time() callback.
In this newly introduced ->init_irq() callback, we call irqchip_init()
which is the default behavior when ->init_irq() isn't defined, and
then do the initialization related to the coherency: SCU, coherency
fabric, and mvebu-mbus (which is needed to start secondary CPUs).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In preparation to a small re-organization of the initialization
sequence in board-v7.c, this commit moves the registration of the
custom external abort handler on Armada 375 later in the boot
sequence, and makes it more similar to the other quirks that we
already have. There is indeed no need to register this abort handler
particularly early, it simply needs to be registered before switching
to userspace.
In addition to this, this commit makes the registration of the custom
abort handler conditional on Armada 375 Z1, because Armada 375 A0 and
later iterations are not affected by the issue.
This commit was tested on both Armada 375 Z1 and Armada 375 A0
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reverts commit d26b17edaf
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
BCM (Kona/capri platform) has regressed in two ways on this release. First,
bcm_defconfig no longer selected the appropriate MMC driver options due to
changes in dependencies. Secondly, the new MFD and regulator drivers were not
enabled on multi_v7_defconfig, so that caused the system to fail probing MMC
there.
Fix by enabling the new options as needed.
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A new set of bug fixes for 3.16, containing patches for seven platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAU6sVyGCrR//JCVInAQIJVw//f/6zO73c9xNdDfDfOV7HHC0W4WQ5RBJE
+VFpj+DKWDKWVgauW/j6FVC2uvwb/v7arEB7Ta/xE2dk/q6VwMzsOJbtFzrrD/Un
s3VP7M4VEzARghQCUhNgGxPw6UCpBNql8JdSo+oMU+TYfSa532EZBT7It3irkjHP
Yfbk7YOvLR7zXjDsTlUtiDSs3XLAD0VqpTGYi8IO3S6wbGa0jWaE3LOq9kSjZlDv
oaFeFafJSx/o9NqLEC3a+IvNxslc6Crhin+3nSp+HDntbdgehdEVgC9aATMhkPXM
IjVPzerHNzCMocxM44vtI0lpDmwPq42Di8IxjWFwtGk+yxJbkAfX/1cn1R5Y5ER8
ZrVBixX9U47Rd8UP6CzCGsmJOS+rU+owlTTup7phBebxVEpWnUjigDSH3Eb956CO
y4M9zJvPgUmhd/AVywHxvRGpPXC1EUcwnF0uUB0EDG22ZfsDmdfjvUqY4Klhcsjo
BvsDNLBGQ6HUhhzEYoOBOPyYsm3yAhyFK1Z451yt5P7R44+lSVmyXWEyEpPrTwl9
+wVGY49pFwd/xV/a7M8BAZYvkbNZU0dcW0ZPMK2mtFzn9vEESRVIPqm0NEOF0HHS
kEX6XpZhkJjfPvsXWTeiCFnYnI0ghlJcWE6lMWbL1dWxqFYlUC9lIjN0PJ44M7oy
cBKPiJ27MIM=
=fJMs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTqvVyAAoJEAf03oE53VmQz+sH/2Di3RkT90URl9bGIiIgYh/S
NYg8gpasHEdxMtiDGp6c7ie9EWpIK1ga1F0Iha0fwYEJE/WOmlqEQYhXuoJyxKpJ
lJ2lfprj7Z19RjA717g+Q2LbAshTI1K3HhP2d56o97KkdmcIB76Re5DoGL14Ez6A
TP0sCTCGWO+brjPPmzDY0la2HezjMKmOnxtdu4sbysHe6RT9b6JcEa1cFsT0nh4j
DKdeyDO/kAp6sbkprkv7WCGpa+6fvsPEsnioO3IlYJx4ayT4Uq64YqS5skuzQK74
7TdTSZoq0OM87t/zY2NR5MGSPoi48fP4Z2O+m/L9PVzROCK44eXBKe4lzOArxKQ=
=D+rW
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
The at91sam9261 doesn't actually have a slow RC oscillator, remove it from the
dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM fixes from Russell King:
"A number of low impact fixes, the most noticable one is the thumb2
frame pointer fix. We also fix a regression caused during this merge
window with ARM925 CPUs running with caches disabled, and fix a number
of warnings"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: arm925: ensure assembly sets up writethrough mapping
ARM: perf: fix compiler warning with gcc 4.6.4 (and tidy code)
ARM: l2c: fix dependencies on PL310 errata symbols
ARM: 8069/1: Make thread_save_fp macro aware of THUMB2 mode
ARM: 8068/1: scoop: Remove unused variable
Commit 07e461cd7e
"of: Ensure unique names without sacrificing determinism"
caused a boot failure regression on the Integrator machines.
The problem is probably caused by fiddling too much with
the device tree population in the OF init function, such
as passing the SoC bus device as parent when populating
the device tree.
This patch fixes the problem by:
- Avoiding to explicitly look up the tree root
- Look up devices needed before device population from
the match only, passing NULL as root
- Passing NULL as root and parent when calling
of_platform_populate()
After this the Integrators boot again. Tested on
Integrator/AP and Integrator/CP.
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
