This patch adds the device tree to support Toradex Colibri T30, a
computer on module which can be used on different carrier boards.
The module consists of a Tegra 30 SoC, two PMIC, DDR3L RAM, eMMC,
a LM95245 temperature sensor and an AX88772B USB Ethernet
Controller. Furthermore, there is a STMPE811 and SGTL5000 audio
codec which are not yet supported. Anything that is not self
contained on the module is disabled by default.
The device tree for the Evaluation Board includes the modules
device tree and enables the supported pheripherials of the carrier
board (the Evaluation Board supports almost all of them).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The last reason for static memory mapping is the HBI (board
identification number) check early in the machine code.
Moving the check to the sysreg driver makes it possible to
completely remove the early mapping and init functions.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
As all cores must be properly described in the Device Tree,
there is no point in getting their numbers from SCU on
A5/A9 platforms. This significantly simplifies the code,
removing the need for flat-tree scanning and early static
mapping.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
arm_dt_init_cpu_maps parses the device tree, validates and sets the
cpu_possible_mask appropriately. It is unnecessary to do another DT
parse to get the number of cpus, use num_possible_cpus instead.
This patch also removes setting cpu_present_mask as platforms should
only re-initialize it in smp_prepare_cpus() if present != possible.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch adds a trival sched clock source using free
running, 24MHz clocked counter present in the ARM Ltd.
reference platforms (Versatile, RealView, Versatile
Express) System Registers block.
This code replaces the call in the VE machine code.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:
* LEDs code has been completely removed and replaced with
"gpio-leds" nodes in the tree (referencing dedicated
GPIO subnodes in sysreg - bindings documentation updated);
this also better fits the reality as some variants of the
motherboard don't have all the LEDs populated
* syscfg bridge code has been extracted into a separate
driver (placed in drivers/misc for no better place)
* all the ID & MISC registers are defined as sysconf
making them available for other drivers should they need
to use them (and also to the user via /sys/kernel/debug/regmap
which can be helpful in platform debugging)
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
Select the MFD_SUN6I_PRCM option when sun6i arch is enabled in order to get
the PRCM (Power/Reset/Clock Management) related drivers compiled.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PSCIv0.2 adds a new function called AFFINITY_INFO, which
can be used to query if a specified CPU has actually gone
offline. Calling this function via cpu_kill ensures that
a CPU has quiesced after a call to cpu_die. This helps
prevent the CPU from doing arbitrary bad things when data
or instructions are clobbered (as happens with kexec)
in the window between a CPU announcing that it is dead
and said CPU leaving the kernel.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The PSCIv0.2 spec defines standard values of function IDs
and introduces a few new functions. Detect version of PSCI
and appropriately select the right PSCI functions.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The A31 SoC has a different pin controller for PL and PM banks.
Define this new controller in the device tree.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add DT definitions for PRCM (Power/Reset/Clock Management) clock and reset
controller subdevices.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For SOCs with dt enabled, device should be build through device tree.
Prevent device build call from platform code, if device tree is
enabled.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB pinmux information and USB modes
for the USB controllers.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for the Super Speed USB controllers, omap-control-usb,
USB2 PHY and USB3 PHY devices.
Remove ocp2scp1 address space from hwmod data as it is
now provided via device tree.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This clock gate description is missing in the older Reference manuals.
It is present on the SoC to provide 960MHz reference clock to the
internal USB PHYs.
Reference: DRA75x_DRA74x_ES1.1_NDA_TRM_vO.pdf, pg. 900,
Table 3-812. CM_COREAON_L3INIT_60M_GFCLK_CLKCTRL
Use l3init_960m_gfclk as parent of usb_otg_ss1_refclk960m and
usb_otg_ss2_refclk960m.
CC: Benoît Cousson <bcousson@baylibre.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB2 PHY driver expects named clocks for wakeup clock
and reference clock. Provide this information for USB2 PHY
nodes in OMAP4 and OMAP5 SoC DTS.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.
[Roger Q] Clean up. Updated IRQ for interrupt crossbar.
CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for sata.
[Roger Q] Clean up.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
G2D power domain also controls the CMU block of G2D. Since
clock registers can be accessed anytime for viewing
clk_summary, it can cause a system crash if g2d power domain
is disabled.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MAU powerdomain provides clocks for Audio sub-system block.
This block comprises of the I2S audio controller, audio DMA
blocks and Audio sub-system clock registers.
Right now, there is no way to hook up power-domains with
clock providers. During late boot when this power-domain
gets disabled, we get following external abort.
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
High speed I2C is used on Exynos5 based SoCs. Enable it.
The MMC partition for Root filesystem cannot be mounted
without this enabling HS-I2C and regulators on many boards
are connected HS-I2C bus so the regulators don't come by
default without this.
Actually, we are not able to get arndale-octa board to boot
and mount an MMC partition without this change.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Javi Merino <javi.merino@arm.com>
[kgene.kim@samsung.com: modified description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This change places MDMA1 in disabled node for Exynos5420.
If MDMA1 region is configured with secure mode, it makes
the boot failure with the following on smdk5420 board.
("Unhandled fault: imprecise external abort (0x1406) at 0x00000000")
Thus, arndale-octa board don't need to do the same thing anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the offset of CPU boot address and changes
the parameter of smc call for SMC_CMD_CPU1BOOT command on
exynos4212.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of hardcoding the SYSRAM details for each SoC,
pass this information through device tree (DT) and make
the code SoC agnostic. Generic DT SRAM bindings are
used for achieving this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add hwmod data for dss core, dispc dsi1, dsi2, rfbi and hdmi. It's more
or less similar to omap4 hwmod data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
All audio related omap_hwmod_ocp_if *_dma can be removed from the data since
we can just add the user flag to the non dma structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch moves S3C24XX specific clock Kconfig options into
"clk/samsung/Kconfig" and also removes COMMON_CLK selection from
"mach-s3c24xx/Kconfig" as S3C24XX_COMMON_CLK is selecting it's dependency.
CC: Ben Dooks <ben-linux@fluff.org>
CC: Kukjin Kim <kgene.kim@samsung.com>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch selects COMMON_CLK_SAMSUNG for EXYNOS and S3C64XX SoC
and removes COMMON_CLK selection as COMMON_CLK_SAMSUNG selects it's dependency.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
After full migration of s3c24xx to Common Clock Framework, some unneeded
entries in Kconfig still remained. Delete them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch includes,
1] renaming of the HSI2C clocks
2] renaming of spi clocks according to the datasheet
3] fixes for child-parent relationships
4] adding of more clocks related to PERIC block
5] use GATE_IP_* offsets instead of GATE_BUS_*
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AT24C EEPROM:
This is used for the board ID EEPROM on Jetson TK1, as well as likely
a whole slew of other NVIDIA reference boards; we simply haven't added
enabled the EEPROM in the DT files until now.
MTD_SPI_NOR:
This defconfig contains the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to satisfy
the new dependency.
FRAMEBUFFER_CONSOLE_ROTATION:
Needed for devices like Tegra Note 7 and NVIDIA SHIELD to get the boot
console in the expected orientation.
CAN*, RTC_DRV_DS1307:
Toradex Colibri Evaluation Board uses the DS1307 RTC and the MCP251x CAN
controller. The NVIDIA Tegra 3 based Colibri T30 module can be used on
this carrier board.
Furthermore the NVIDIA Tegra 3 based Apalis T30 module too contains two
MCP251x CAN controllers.
INPUT_JOYDEV:
NVIDIA SHIELD embeds a USB joystick device.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The APP4 EVB1 development boards embeds an A31, together with some NAND, one SD
card slot, and one SDIO + UART WiFi and Bluetooth chip, a few I2C buses, USB,
and a LCD display.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The A31 has two ECHI/OHCI controllers, and one OHCI-only phy-less controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The USB clocks of the A31 seems to be parented to the 24MHz oscillator, and
handle the clocks for the USB phys and OHCI devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
shmobile_init_delay() looks for OF "clock-frequency" to determine
the delay which is set by calling shmobile_setup_delay().
Unfortunately this seems to be incorrect in detail as
"clock-frequency" node values are in HZ whereas the frequency
argument to shmobile_setup_delay() is in MHz.
Provide a variant of shmobile_setup_delay() that accepts HZ to
correct this problem.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MTU2 is not yet prepared for DT usage, so use the common workaround via
clkdev for now.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
arch/arm/mach-shmobile/board-genmai-reference.c:23:0:
arch/arm/mach-shmobile/include/mach/clock.h:19:54: warning: 'struct clk' declared inside parameter list [enabled by default]
arch/arm/mach-shmobile/include/mach/clock.h:19:54: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Not used anymore since we switched to CCF.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Not used anymore since we switched to CCF.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have now DT support for SCIF, so use the platform_device
initialization only for the legacy support.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We keep the UART naming backwards compatible with the legacy version.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
