linux-pinenote/drivers/block/umem.h

/*
 * This file contains defines for the
 *   Micro Memory MM5415
 * family PCI Memory Module with Battery Backup.
 *
 * Copyright Micro Memory INC 2001.  All rights reserved.
 * Release under the terms of the GNU GENERAL PUBLIC LICENSE version 2.
 * See the file COPYING.
 */

#ifndef _DRIVERS_BLOCK_MM_H
#define _DRIVERS_BLOCK_MM_H


#define IRQ_TIMEOUT (1 * HZ)

/* CSR register definition */
#define MEMCTRLSTATUS_MAGIC	0x00
#define  MM_MAGIC_VALUE		(unsigned char)0x59

#define MEMCTRLSTATUS_BATTERY	0x04
#define  BATTERY_1_DISABLED	0x01
#define  BATTERY_1_FAILURE	0x02
#define  BATTERY_2_DISABLED	0x04
#define  BATTERY_2_FAILURE	0x08

#define MEMCTRLSTATUS_MEMORY	0x07
#define  MEM_128_MB		0xfe
#define  MEM_256_MB		0xfc
#define  MEM_512_MB		0xf8
#define  MEM_1_GB		0xf0
#define  MEM_2_GB		0xe0

#define MEMCTRLCMD_LEDCTRL	0x08
#define  LED_REMOVE		2
#define  LED_FAULT		4
#define  LED_POWER		6
#define	 LED_FLIP		255
#define  LED_OFF		0x00
#define  LED_ON			0x01
#define  LED_FLASH_3_5		0x02
#define  LED_FLASH_7_0		0x03
#define  LED_POWER_ON		0x00
#define  LED_POWER_OFF		0x01
#define  USER_BIT1		0x01
#define  USER_BIT2		0x02

#define MEMORY_INITIALIZED	USER_BIT1

#define MEMCTRLCMD_ERRCTRL	0x0C
#define  EDC_NONE_DEFAULT	0x00
#define  EDC_NONE		0x01
#define  EDC_STORE_READ		0x02
#define  EDC_STORE_CORRECT	0x03

#define MEMCTRLCMD_ERRCNT	0x0D
#define MEMCTRLCMD_ERRSTATUS	0x0E

#define ERROR_DATA_LOG		0x20
#define ERROR_ADDR_LOG		0x28
#define ERROR_COUNT		0x3D
#define ERROR_SYNDROME		0x3E
#define ERROR_CHECK		0x3F

#define DMA_PCI_ADDR		0x40
#define DMA_LOCAL_ADDR		0x48
#define DMA_TRANSFER_SIZE	0x50
#define DMA_DESCRIPTOR_ADDR	0x58
#define DMA_SEMAPHORE_ADDR	0x60
#define DMA_STATUS_CTRL		0x68
#define  DMASCR_GO		0x00001
#define  DMASCR_TRANSFER_READ	0x00002
#define  DMASCR_CHAIN_EN	0x00004
#define  DMASCR_SEM_EN		0x00010
#define  DMASCR_DMA_COMP_EN	0x00020
#define  DMASCR_CHAIN_COMP_EN	0x00040
#define  DMASCR_ERR_INT_EN	0x00080
#define  DMASCR_PARITY_INT_EN	0x00100
#define  DMASCR_ANY_ERR		0x00800
#define  DMASCR_MBE_ERR		0x01000
#define  DMASCR_PARITY_ERR_REP	0x02000
#define  DMASCR_PARITY_ERR_DET	0x04000
#define  DMASCR_SYSTEM_ERR_SIG	0x08000
#define  DMASCR_TARGET_ABT	0x10000
#define  DMASCR_MASTER_ABT	0x20000
#define  DMASCR_DMA_COMPLETE	0x40000
#define  DMASCR_CHAIN_COMPLETE	0x80000

/*
3.SOME PCs HAVE HOST BRIDGES WHICH APPARENTLY DO NOT CORRECTLY HANDLE
READ-LINE (0xE) OR READ-MULTIPLE (0xC) PCI COMMAND CODES DURING DMA
TRANSFERS. IN OTHER SYSTEMS THESE COMMAND CODES WILL CAUSE THE HOST BRIDGE
TO ALLOW LONGER BURSTS DURING DMA READ OPERATIONS. THE UPPER FOUR BITS
(31..28) OF THE DMA CSR HAVE BEEN MADE PROGRAMMABLE, SO THAT EITHER A 0x6,
AN 0xE OR A 0xC CAN BE WRITTEN TO THEM TO SET THE COMMAND CODE USED DURING
DMA READ OPERATIONS.
*/
#define        DMASCR_READ   0x60000000
#define        DMASCR_READLINE   0xE0000000
#define        DMASCR_READMULTI   0xC0000000


#define DMASCR_ERROR_MASK	(DMASCR_MASTER_ABT | DMASCR_TARGET_ABT | DMASCR_SYSTEM_ERR_SIG | DMASCR_PARITY_ERR_DET | DMASCR_MBE_ERR | DMASCR_ANY_ERR)
#define DMASCR_HARD_ERROR	(DMASCR_MASTER_ABT | DMASCR_TARGET_ABT | DMASCR_SYSTEM_ERR_SIG | DMASCR_PARITY_ERR_DET | DMASCR_MBE_ERR)

#define WINDOWMAP_WINNUM	0x7B

#define DMA_READ_FROM_HOST 0
#define DMA_WRITE_TO_HOST 1

struct mm_dma_desc {
	__le64	pci_addr;
	__le64	local_addr;
	__le32	transfer_size;
	u32	zero1;
	__le64	next_desc_addr;
	__le64	sem_addr;
	__le32	control_bits;
	u32	zero2;

	dma_addr_t data_dma_handle;

	/* Copy of the bits */
	__le64	sem_control_bits;
} __attribute__((aligned(8)));

/* bits for card->flags */
#define UM_FLAG_DMA_IN_REGS		1
#define UM_FLAG_NO_BYTE_STATUS		2
#define UM_FLAG_NO_BATTREG		4
#define	UM_FLAG_NO_BATT			8
#endif