Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								/*
							 | 
						
					
						
							
								
									
										
										
										
											2012-01-27 13:36:01 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								 * drivers/net/ethernet/ibm/emac/tah.c
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Driver for PowerPC 4xx on-chip ethernet controller, TAH support.
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							
								
									
										
										
										
											2007-12-05 11:14:33 +11:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								 * Copyright 2007 Benjamin Herrenschmidt, IBM Corp.
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *                <benh@kernel.crashing.org>
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Based on the arch/ppc version of the driver:
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Copyright 2004 MontaVista Software, Inc.
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Matt Porter <mporter@kernel.crashing.org>
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Copyright (c) 2005 Eugene Surovegin <ebs@ebshome.net>
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 *
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * This program is free software; you can redistribute  it and/or modify it
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * under  the terms of  the GNU General  Public License as published by the
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * Free Software Foundation;  either version 2 of the  License, or (at your
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 * option) any later version.
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 */
							 | 
						
					
						
							
								
									
										
										
										
											2013-09-17 14:28:33 -05:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								#include <linux/of_address.h>
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								#include <asm/io.h>
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								#include "emac.h"
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								#include "core.h"
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2012-12-03 09:23:13 -05:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								int tah_attach(struct platform_device *ofdev, int channel)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev = platform_get_drvdata(ofdev);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									mutex_lock(&dev->lock);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									/* Reset has been done at probe() time... nothing else to do for now */
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									++dev->users;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									mutex_unlock(&dev->lock);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return 0;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2010-08-06 09:25:50 -06:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								void tah_detach(struct platform_device *ofdev, int channel)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev = platform_get_drvdata(ofdev);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									mutex_lock(&dev->lock);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									--dev->users;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									mutex_unlock(&dev->lock);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2010-08-06 09:25:50 -06:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								void tah_reset(struct platform_device *ofdev)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev = platform_get_drvdata(ofdev);
							 | 
						
					
						
							
								
									
										
										
										
											2007-10-14 19:36:10 +01:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_regs __iomem *p = dev->base;
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									int n;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									/* Reset TAH */
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									out_be32(&p->mr, TAH_MR_SR);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									n = 100;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									while ((in_be32(&p->mr) & TAH_MR_SR) && n)
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										--n;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									if (unlikely(!n))
							 | 
						
					
						
							
								
									
										
										
										
											2010-04-13 16:12:29 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
										printk(KERN_ERR "%s: reset timeout\n",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
											ofdev->dev.of_node->full_name);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2011-03-30 22:57:33 -03:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									/* 10KB TAH TX FIFO accommodates the max MTU of 9000 */
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									out_be32(&p->mr,
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										 TAH_MR_CVR | TAH_MR_ST_768 | TAH_MR_TFS_10KB | TAH_MR_DTFP |
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										 TAH_MR_DIG);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2010-08-06 09:25:50 -06:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								int tah_get_regs_len(struct platform_device *ofdev)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return sizeof(struct emac_ethtool_regs_subhdr) +
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										sizeof(struct tah_regs);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2010-08-06 09:25:50 -06:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								void *tah_dump_regs(struct platform_device *ofdev, void *buf)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev = platform_get_drvdata(ofdev);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									struct emac_ethtool_regs_subhdr *hdr = buf;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									struct tah_regs *regs = (struct tah_regs *)(hdr + 1);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									hdr->version = 0;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									hdr->index = 0; /* for now, are there chips with more than one
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
											 * zmii ? if yes, then we'll add a cell_index
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
											 * like we do for emac
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
											 */
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									memcpy_fromio(regs, dev->base, sizeof(struct tah_regs));
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return regs + 1;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2012-12-03 09:23:13 -05:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								static int tah_probe(struct platform_device *ofdev)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2010-04-13 16:12:29 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct device_node *np = ofdev->dev.of_node;
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									struct resource regs;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									int rc;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									rc = -ENOMEM;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									dev = kzalloc(sizeof(struct tah_instance), GFP_KERNEL);
							 | 
						
					
						
							
								
									
										
										
										
											2012-01-29 12:56:23 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									if (dev == NULL)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
										goto err_gone;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									mutex_init(&dev->lock);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									dev->ofdev = ofdev;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									rc = -ENXIO;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									if (of_address_to_resource(np, 0, ®s)) {
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										printk(KERN_ERR "%s: Can't get registers address\n",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										       np->full_name);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										goto err_free;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									rc = -ENOMEM;
							 | 
						
					
						
							
								
									
										
										
										
											2007-10-14 19:36:10 +01:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									dev->base = (struct tah_regs __iomem *)ioremap(regs.start,
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
													       sizeof(struct tah_regs));
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									if (dev->base == NULL) {
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										printk(KERN_ERR "%s: Can't map device registers!\n",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										       np->full_name);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										goto err_free;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									platform_set_drvdata(ofdev, dev);
							 | 
						
					
						
							
								
									
										
										
										
											2007-12-05 11:14:32 +11:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									/* Initialize TAH and enable IPv4 checksum verification, no TSO yet */
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									tah_reset(ofdev);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									printk(KERN_INFO
							 | 
						
					
						
							
								
									
										
										
										
											2010-04-13 16:12:29 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									       "TAH %s initialized\n", ofdev->dev.of_node->full_name);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									wmb();
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return 0;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 err_free:
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									kfree(dev);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								 err_gone:
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return rc;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2012-12-03 09:23:13 -05:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								static int tah_remove(struct platform_device *ofdev)
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2013-05-23 00:52:31 +00:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									struct tah_instance *dev = platform_get_drvdata(ofdev);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									WARN_ON(dev->users != 0);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									iounmap(dev->base);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									kfree(dev);
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									return 0;
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								static struct of_device_id tah_match[] =
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2008-03-13 16:59:43 +01:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									{
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										.compatible	= "ibm,tah",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									},
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									/* For backward compat with old DT */
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									{
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										.type		= "tah",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									},
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									{},
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								};
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							
								
									
										
										
										
											2011-02-22 21:05:51 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
								static struct platform_driver tah_driver = {
							 | 
						
					
						
							
								
									
										
										
										
											2010-04-13 16:13:02 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									.driver = {
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										.name = "emac-tah",
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										.owner = THIS_MODULE,
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
										.of_match_table = tah_match,
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									},
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
									.probe = tah_probe,
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
									.remove = tah_remove,
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								};
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								int __init tah_init(void)
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2011-02-22 21:05:51 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									return platform_driver_register(&tah_driver);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								void tah_exit(void)
							 | 
						
					
						
							| 
								
							 | 
							
								
							 | 
							
								
							 | 
							
							
								{
							 | 
						
					
						
							
								
									
										
										
										
											2011-02-22 21:05:51 -07:00
										 
									 
								 
							 | 
							
								
									
										
									
								
							 | 
							
								
							 | 
							
							
									platform_driver_unregister(&tah_driver);
							 | 
						
					
						
							
								
									
										
											 
										 
										
											
												Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
											
										 
										
											2007-08-23 13:56:01 +10:00
										 
									 
								 
							 | 
							
								
							 | 
							
								
							 | 
							
							
								}
							 |