forge/linux-pinenote
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
linux-pinenote/drivers/infiniband/ulp/ipoib/Kconfig

50 lines
1.8 KiB
Text
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
config INFINIBAND_IPOIB
tristate "IP-over-InfiniBand"
IB: Use menuconfig for InfiniBand menu Change Kconfig objects from "menu, config" into "menuconfig" so that the user can disable the whole feature without having to enter the menu first. Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-23 14:21:22 -07:00
depends on NETDEVICES && INET && (IPV6 || IPV6=n)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
---help---
Support for the IP-over-InfiniBand protocol (IPoIB). This
transports IP packets over InfiniBand so you can use your IB
device as a fancy NIC.
IB/ipoib: Remove broken link from Kconfig and documentation Remove references to the IPoIB IETF working group as it has been closed. Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-07-13 11:00:39 +03:00
See Documentation/infiniband/ipoib.txt for more information
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
IPoIB: Connected mode experimental support The following patch adds experimental support for IPoIB connected mode, as defined by the draft from the IETF ipoib working group. The idea is to increase performance by increasing the MTU from the maximum of 2K (theoretically 4K) supported by IPoIB on top of UD. With this code, I'm able to get 800MByte/sec or more with netperf without options on a Mellanox 4x back-to-back DDR system. Some notes on code: 1. SRQ is used for scalability to large cluster sizes 2. Only RC connections are used (UC does not support SRQ now) 3. Retry count is set to 0 since spec draft warns against retries 4. Each connection is used for data transfers in only 1 direction, so each connection is either active(TX) or passive (RX). 2 sides that want to communicate create 2 connections. 5. Each active (TX) connection has a separate CQ for send completions - this keeps the code simple without CQ resize and other tricks 6. To detect stale passive side connections (where the remote side is down), we keep an LRU list of passive connections (updated once per second per connection) and destroy a connection after it has been unused for several seconds. The LRU rule makes it possible to avoid scanning connections that have recently been active. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-05 22:12:23 +02:00
config INFINIBAND_IPOIB_CM
bool "IP-over-InfiniBand Connected Mode support"
IPoIB/cm: Connected mode is no longer EXPERIMENTAL Connected mode is now tested and used by lots of people. No need to hide it under CONFIG_EXPERIMENTAL. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
depends on INFINIBAND_IPOIB
IPoIB: Connected mode experimental support The following patch adds experimental support for IPoIB connected mode, as defined by the draft from the IETF ipoib working group. The idea is to increase performance by increasing the MTU from the maximum of 2K (theoretically 4K) supported by IPoIB on top of UD. With this code, I'm able to get 800MByte/sec or more with netperf without options on a Mellanox 4x back-to-back DDR system. Some notes on code: 1. SRQ is used for scalability to large cluster sizes 2. Only RC connections are used (UC does not support SRQ now) 3. Retry count is set to 0 since spec draft warns against retries 4. Each connection is used for data transfers in only 1 direction, so each connection is either active(TX) or passive (RX). 2 sides that want to communicate create 2 connections. 5. Each active (TX) connection has a separate CQ for send completions - this keeps the code simple without CQ resize and other tricks 6. To detect stale passive side connections (where the remote side is down), we keep an LRU list of passive connections (updated once per second per connection) and destroy a connection after it has been unused for several seconds. The LRU rule makes it possible to avoid scanning connections that have recently been active. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-05 22:12:23 +02:00
default n
---help---
IPoIB/cm: Connected mode is no longer EXPERIMENTAL Connected mode is now tested and used by lots of people. No need to hide it under CONFIG_EXPERIMENTAL. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
This option enables support for IPoIB connected mode. After
enabling this option, you need to switch to connected mode
through /sys/class/net/ibXXX/mode to actually create
connections, and then increase the interface MTU with
e.g. ifconfig ib0 mtu 65520.
IPoIB: Connected mode experimental support The following patch adds experimental support for IPoIB connected mode, as defined by the draft from the IETF ipoib working group. The idea is to increase performance by increasing the MTU from the maximum of 2K (theoretically 4K) supported by IPoIB on top of UD. With this code, I'm able to get 800MByte/sec or more with netperf without options on a Mellanox 4x back-to-back DDR system. Some notes on code: 1. SRQ is used for scalability to large cluster sizes 2. Only RC connections are used (UC does not support SRQ now) 3. Retry count is set to 0 since spec draft warns against retries 4. Each connection is used for data transfers in only 1 direction, so each connection is either active(TX) or passive (RX). 2 sides that want to communicate create 2 connections. 5. Each active (TX) connection has a separate CQ for send completions - this keeps the code simple without CQ resize and other tricks 6. To detect stale passive side connections (where the remote side is down), we keep an LRU list of passive connections (updated once per second per connection) and destroy a connection after it has been unused for several seconds. The LRU rule makes it possible to avoid scanning connections that have recently been active. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-05 22:12:23 +02:00
IPoIB/cm: Connected mode is no longer EXPERIMENTAL Connected mode is now tested and used by lots of people. No need to hide it under CONFIG_EXPERIMENTAL. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
WARNING: Enabling connected mode will trigger some packet
drops for multicast and UD mode traffic from this interface,
IPoIB: Connected mode experimental support The following patch adds experimental support for IPoIB connected mode, as defined by the draft from the IETF ipoib working group. The idea is to increase performance by increasing the MTU from the maximum of 2K (theoretically 4K) supported by IPoIB on top of UD. With this code, I'm able to get 800MByte/sec or more with netperf without options on a Mellanox 4x back-to-back DDR system. Some notes on code: 1. SRQ is used for scalability to large cluster sizes 2. Only RC connections are used (UC does not support SRQ now) 3. Retry count is set to 0 since spec draft warns against retries 4. Each connection is used for data transfers in only 1 direction, so each connection is either active(TX) or passive (RX). 2 sides that want to communicate create 2 connections. 5. Each active (TX) connection has a separate CQ for send completions - this keeps the code simple without CQ resize and other tricks 6. To detect stale passive side connections (where the remote side is down), we keep an LRU list of passive connections (updated once per second per connection) and destroy a connection after it has been unused for several seconds. The LRU rule makes it possible to avoid scanning connections that have recently been active. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-05 22:12:23 +02:00
unless you limit mtu for these destinations to 2044.
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
config INFINIBAND_IPOIB_DEBUG
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option is used to configure any non-standard kernel with a much larger scope than only small devices. This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes references to the option throughout the kernel. A new CONFIG_EMBEDDED option is added that automatically selects CONFIG_EXPERT when enabled and can be used in the future to isolate options that should only be considered for embedded systems (RISC architectures, SLOB, etc). Calling the option "EXPERT" more accurately represents its intention: only expert users who understand the impact of the configuration changes they are making should enable it. Reviewed-by: Ingo Molnar <mingo@elte.hu> Acked-by: David Woodhouse <david.woodhouse@intel.com> Signed-off-by: David Rientjes <rientjes@google.com> Cc: Greg KH <gregkh@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jens Axboe <axboe@kernel.dk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Robin Holt <holt@sgi.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-20 14:44:16 -08:00
bool "IP-over-InfiniBand debugging" if EXPERT
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
depends on INFINIBAND_IPOIB
IPoIB: Always build debugging code unless CONFIG_EMBEDDED=y Don't allow CONFIG_INFINIBAND_IPOIB_DEBUG to be disabled unless CONFIG_EMBEDDED is selected. We want users (and especially distros) to have this turned on unless they really need to save space, because by the time we want debugging output, it's usually too late to rebuild a kernel. The debugging output can be controlled at runtime via the debug_level module parameter in sysfs. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-02 14:39:19 -07:00
default y
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
---help---
This option causes debugging code to be compiled into the
IPoIB driver. The output can be turned on via the
debug_level and mcast_debug_level module parameters (which
can also be set after the driver is loaded through sysfs).
IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs," which no longer exists. Correct this to talk about the files under debugfs that are really created. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
This option also creates a directory tree under ipoib/ in
debugfs, which contains files that expose debugging
information about IB multicast groups used by the IPoIB
driver.
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
config INFINIBAND_IPOIB_DEBUG_DATA
bool "IP-over-InfiniBand data path debugging"
depends on INFINIBAND_IPOIB_DEBUG
---help---
Still more typo fixes Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 22:36:44 +02:00
This option compiles debugging code into the data path
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
of the IPoIB driver. The output can be turned on via the
data_debug_level module parameter; however, even with output
turned off, this debugging code will have some performance
impact.
Reference in a new issue Copy permalink